Compare commits
2
Commits
bd773982f8
...
6a52f1af0b
| Author | SHA1 | Date | |
|---|---|---|---|
|
|
6a52f1af0b | ||
|
|
b8e045d8d6 |
No files matched your search
+7
-6
@@ -27,15 +27,16 @@ works if the case stays out of the sun.
|
|||||||
|
|
||||||
## Hardware
|
## Hardware
|
||||||
|
|
||||||
- 10 × M3 heat-set inserts (about 4.6 mm OD, 5.7 mm long; the holes are 4.0 mm
|
- 12 × M3 heat-set inserts, CNC Kitchen M3 × 5.7 (about 4.6 mm OD; the holes
|
||||||
and 6 mm deep):
|
are 4.2 mm and 6 mm deep, set by `insert_d` if your printer runs tighter or
|
||||||
|
looser):
|
||||||
- 4 in the bezel's display bosses
|
- 4 in the bezel's display bosses
|
||||||
- 2 in the bezel's feet
|
- 2 in the bezel's feet
|
||||||
- 2 in the body's rear corners
|
- 2 in the body's rear corners
|
||||||
- 4 on the base's board standoffs
|
- 4 on the base's board standoffs
|
||||||
- 4 × M3×8 to bolt the display to the bezel
|
- 4 × M3×6 to bolt the display to the bezel
|
||||||
- 4 × M3×6 to hold the D1 board on its standoffs
|
- 4 × M3×6 to hold the D1 board on its standoffs
|
||||||
- 4 × M3×8 to hold the base on, from below; **M3×10** with the TPU feet
|
- 4 × M3×8 to hold the base on, from below (also with the TPU feet)
|
||||||
|
|
||||||
## Assembly
|
## Assembly
|
||||||
|
|
||||||
@@ -48,8 +49,8 @@ works if the case stays out of the sun.
|
|||||||
the anchor on the base.
|
the anchor on the base.
|
||||||
6. Put the body on the base and screw it together from below. The base holds
|
6. Put the body on the base and screw it together from below. The base holds
|
||||||
the bezel in place. With the feet, put a foot on each screw first (the
|
the bezel in place. With the feet, put a foot on each screw first (the
|
||||||
spigot faces the base) and use M3×10. Tighten until the foot is snug; the
|
spigot faces the base); M3×8 is still long enough. Tighten until the foot
|
||||||
TPU only needs light compression.
|
is snug; the TPU only needs light compression.
|
||||||
|
|
||||||
## Measure before printing
|
## Measure before printing
|
||||||
|
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
Binary file not shown.
+3
-3
@@ -8,7 +8,7 @@
|
|||||||
// Assembly:
|
// Assembly:
|
||||||
// 1. Melt M3 heat-set inserts into: 4 display bosses + 2 feet on the bezel,
|
// 1. Melt M3 heat-set inserts into: 4 display bosses + 2 feet on the bezel,
|
||||||
// 2 rear corner bosses in the body, 4 board standoffs on the base.
|
// 2 rear corner bosses in the body, 4 board standoffs on the base.
|
||||||
// 2. Bolt the display to the bezel from behind (4x M3x8).
|
// 2. Bolt the display to the bezel from behind (4x M3x6).
|
||||||
// 3. Screw the D1 board onto the base (4x M3x6).
|
// 3. Screw the D1 board onto the base (4x M3x6).
|
||||||
// 4. Slide the bezel (with display) up into the body's side grooves from below.
|
// 4. Slide the bezel (with display) up into the body's side grooves from below.
|
||||||
// 5. Wire up, put the body on the base and screw it together from below (4x M3x8).
|
// 5. Wire up, put the body on the base and screw it together from below (4x M3x8).
|
||||||
@@ -55,14 +55,14 @@ win_r = 2;
|
|||||||
win_chamfer = 1.5;
|
win_chamfer = 1.5;
|
||||||
|
|
||||||
/* [Heat-set inserts, M3] */
|
/* [Heat-set inserts, M3] */
|
||||||
insert_d = 4.0; // hole for the insert
|
insert_d = 4.2; // hole for the insert (CNC Kitchen M3x5.7; 4.0 printed too tight)
|
||||||
insert_depth = 6;
|
insert_depth = 6;
|
||||||
boss_d = 7; // display bosses (larger would touch the glass)
|
boss_d = 7; // display bosses (larger would touch the glass)
|
||||||
screw_d = 3.4; // M3 clearance
|
screw_d = 3.4; // M3 clearance
|
||||||
head_d = 6.2; // M3 head counterbore in the base
|
head_d = 6.2; // M3 head counterbore in the base
|
||||||
head_depth = 2;
|
head_depth = 2;
|
||||||
|
|
||||||
/* [TPU feet, held by the base screws (use M3x10 instead of M3x8)] */
|
/* [TPU feet, held by the base screws (M3x8 still fits)] */
|
||||||
foot_d = 14; // fits inside the base outline at the rear corners
|
foot_d = 14; // fits inside the base outline at the rear corners
|
||||||
foot_h = 4.5; // below the base
|
foot_h = 4.5; // below the base
|
||||||
foot_spigot_h = 1.8; // locates in the base's screw counterbore
|
foot_spigot_h = 1.8; // locates in the base's screw counterbore
|
||||||
|
|||||||
Reference in new issue
Block a user