Compare commits
2
Commits
| Author | SHA1 | Date | |
|---|---|---|---|
|
|
640ac243be | ||
|
|
4aaa1a4610 |
No files matched your search
@@ -48,7 +48,7 @@ server, so `type: git` with a URL, not `github://`). The layout must stay
|
||||
to line 2 and from the end of line 2 back home, and nothing scrolls. The
|
||||
buffered text API depends on this; the scroll modes are only for raw writes.
|
||||
- The RXD input is RS-232. The reference build uses a MAX3232 (no inversion
|
||||
in config); a directly wired ESP32 pin needs `inverted: true` on the UART TX
|
||||
in config); a directly wired ESP8266 pin needs `inverted: true` on the UART TX
|
||||
pin. Baud rate and parity come from the board's jumpers, so they are not
|
||||
validated by the component.
|
||||
- User characters: up to 4, codes 0x20–0x7E. Each is 5 column bytes, bit 6 =
|
||||
|
||||
@@ -42,7 +42,7 @@ external_components:
|
||||
|
||||
uart:
|
||||
id: uart_vfd
|
||||
tx_pin: GPIO17
|
||||
tx_pin: GPIO2 # D1 R1 pin D9 (UART1 TX on the ESP8266)
|
||||
baud_rate: 9600 # match the display's jumpers (factory default: 9600, no parity)
|
||||
|
||||
time: # required by the component (used by samsung_vfd.printf)
|
||||
@@ -54,6 +54,10 @@ samsung_vfd:
|
||||
uart_id: uart_vfd
|
||||
```
|
||||
|
||||
The `uart:` block above uses the pin from the reference build, a WEMOS D1 R1
|
||||
(ESP8266); see [Hardware](#hardware). Any ESPHome board with a free TX pin
|
||||
works.
|
||||
|
||||
For a complete device, copy [examples/samsung-vfd.yaml](examples/samsung-vfd.yaml)
|
||||
into your ESPHome config folder. Add the keys from
|
||||
[examples/secrets.yaml.example](examples/secrets.yaml.example) to your
|
||||
@@ -65,13 +69,16 @@ The board in the photos is a 20L203DA5 (rev A). The included
|
||||
[datasheet](docs/20L203DA12-datasheet.pdf) is for the 20L203DA12, a variant
|
||||
with the same command set.
|
||||
|
||||
The reference build drives it from a WEMOS D1 R1, an UNO-sized ESP8266 board,
|
||||
through a MAX3232. The [desk case](case/README.md) is made for that board.
|
||||
|
||||
### Connector (3-pin Molex 5046-03A)
|
||||
|
||||
| Pin | Signal | Connect to |
|
||||
|-----|--------|------------|
|
||||
| 1 | VCC | 5–24 V DC supply |
|
||||
| 2 | RXD | MAX3232 T1OUT (T1IN ← ESP32 GPIO17), see below |
|
||||
| 3 | GND | supply GND, MAX3232 GND **and** ESP32 GND |
|
||||
| 2 | RXD | MAX3232 T1OUT (T1IN ← D1 R1 GPIO2), see below |
|
||||
| 3 | GND | supply GND, MAX3232 GND **and** D1 R1 GND |
|
||||
|
||||
### Power
|
||||
|
||||
@@ -83,21 +90,21 @@ for example 12 V at 1 A, and connect the grounds together.
|
||||
### Signal levels
|
||||
|
||||
The RXD input goes through an RS-232 receiver: it expects ±3 to ±15 V and
|
||||
idles at the negative level (mark). It tolerates ±30 V, so a 3.3 V ESP32 pin
|
||||
idles at the negative level (mark). It tolerates ±30 V, so a 3.3 V ESP8266 pin
|
||||
can't damage it. There are two ways to connect it:
|
||||
|
||||
- **Through a MAX3232 (recommended, and how the original build is wired).**
|
||||
Power the MAX3232 from the ESP32's 3.3 V, then wire GPIO17 → T1IN and
|
||||
Power the MAX3232 from the D1's 3.3 V, then wire GPIO2 → T1IN and
|
||||
T1OUT → display RXD. The MAX3232 produces real RS-232 levels and does the
|
||||
inversion itself, so use the plain `tx_pin: GPIO17`.
|
||||
- **Direct from the ESP32.** A plain TTL signal arrives inverted, so wire
|
||||
GPIO17 straight to RXD and invert the pin in the UART config:
|
||||
inversion itself, so use the plain `tx_pin: GPIO2`.
|
||||
- **Direct from the ESP8266.** A plain TTL signal arrives inverted, so wire
|
||||
GPIO2 straight to RXD and invert the pin in the UART config:
|
||||
|
||||
```yaml
|
||||
uart:
|
||||
id: uart_vfd
|
||||
tx_pin:
|
||||
number: GPIO17
|
||||
number: GPIO2
|
||||
inverted: true
|
||||
baud_rate: 9600
|
||||
```
|
||||
@@ -109,6 +116,14 @@ can't damage it. There are two ways to connect it:
|
||||
If the display shows garbage or nothing at all, the inversion setting is the
|
||||
first thing to check: off with a MAX3232, on without one.
|
||||
|
||||
### Why GPIO2
|
||||
|
||||
The ESP8266 has two hardware UARTs. UART0 (GPIO1/GPIO3) is the USB serial
|
||||
port that ESPHome's logger uses. UART1 can only transmit, and only on GPIO2,
|
||||
which is all this display needs. On the D1 R1, GPIO2 is the pin labelled D9.
|
||||
GPIO2 must be high at boot; the MAX3232's input doesn't pull it low, so that
|
||||
is fine.
|
||||
|
||||
### Jumpers
|
||||
|
||||
The 2×8 pin header on the board selects the following. Jumpers are read only
|
||||
@@ -209,7 +224,7 @@ table, character set and user characters. It sends them again after
|
||||
| `samsung_vfd.set_blink` | `interval:` (templatable time): on for that long, off for that long, in 13 ms steps up to 3.3 s. `0ms` stops blinking. |
|
||||
| `samsung_vfd.turn_off` / `turn_on` | Blanks the screen and brings it back without losing its contents. |
|
||||
| `samsung_vfd.set_annunciator` | `column:` 1–20, or 0 for all; `state:` true/false (both templatable). Switches the triangle under that column. |
|
||||
| `samsung_vfd.reinit` | Resets the display, re-applies all settings and redraws the screen. Use it when the display was power-cycled without the ESP. |
|
||||
| `samsung_vfd.reinit` | Resets the display, re-applies all settings and redraws the screen. Use it when the display was power-cycled without the ESP8266. |
|
||||
| `samsung_vfd.self_test` | Runs the built-in self-test (about 20 s), then restores settings and the screen. |
|
||||
|
||||
### Raw control
|
||||
|
||||
+4
-4
@@ -20,23 +20,23 @@ at least 210 × 115 mm.
|
||||
| [stl/body.stl](stl/body.stl) | upside down, top on the bed (as exported) | Sides, top and back wall. No supports needed. |
|
||||
| [stl/bezel.stl](stl/bezel.stl) | face down (as exported) | Front panel with the window and the display bosses. |
|
||||
| [stl/base.stl](stl/base.stl) | flat (as exported) | Floor with the board standoffs and the screw holes. |
|
||||
| [stl/feet.stl](stl/feet.stl) | flat side down (as exported) | 4 feet, print in **TPU**. Each clamps under one of the base screws, with a spigot that locates in the screw's counterbore. |
|
||||
| [stl/feet.stl](stl/feet.stl) | flat side down (as exported) | 6 feet, print in **TPU**. Each clamps under one of the base screws, with a spigot that locates in the screw's counterbore. |
|
||||
|
||||
PETG is a good choice: the display warms the inside by a few degrees. PLA
|
||||
works if the case stays out of the sun.
|
||||
|
||||
## Hardware
|
||||
|
||||
- 12 × M3 heat-set inserts, CNC Kitchen M3 × 5.7 (about 4.6 mm OD; the holes
|
||||
- 14 × M3 heat-set inserts, CNC Kitchen M3 × 5.7 (about 4.6 mm OD; the holes
|
||||
are 4.2 mm and 6 mm deep, set by `insert_d` if your printer runs tighter or
|
||||
looser):
|
||||
- 4 in the bezel's display bosses
|
||||
- 2 in the bezel's feet
|
||||
- 2 in the body's rear corners
|
||||
- 2 in the body's rear corners and 2 in its side walls, behind the display
|
||||
- 4 on the base's board standoffs
|
||||
- 4 × M3×6 to bolt the display to the bezel
|
||||
- 4 × M3×6 to hold the D1 board on its standoffs
|
||||
- 4 × M3×8 to hold the base on, from below (also with the TPU feet)
|
||||
- 6 × M3×8 to hold the base on, from below (also with the TPU feet)
|
||||
|
||||
## Assembly
|
||||
|
||||
|
||||
Binary file not shown.
Binary file not shown.
Binary file not shown.
+27
-11
@@ -7,11 +7,11 @@
|
||||
//
|
||||
// Assembly:
|
||||
// 1. Melt M3 heat-set inserts into: 4 display bosses + 2 feet on the bezel,
|
||||
// 2 rear corner bosses in the body, 4 board standoffs on the base.
|
||||
// 2 rear corner + 2 front side bosses in the body, 4 board standoffs on the base.
|
||||
// 2. Bolt the display to the bezel from behind (4x M3x6).
|
||||
// 3. Screw the D1 board onto the base (4x M3x6).
|
||||
// 4. Slide the bezel (with display) up into the body's side grooves from below.
|
||||
// 5. Wire up, put the body on the base and screw it together from below (4x M3x8).
|
||||
// 5. Wire up, put the body on the base and screw it together from below (6x M3x8).
|
||||
//
|
||||
// Render one part: openscad -D 'part="body"' -o body.stl vfd-case.scad
|
||||
// Parts: "assembly" (preview with dummy display + board), "body", "bezel", "base",
|
||||
@@ -107,9 +107,17 @@ foot_n = n_bezel_in + 6; // insert axis in the beze
|
||||
foot_y = foot_n / cos(tilt);
|
||||
foot_xs = [inner_w * 0.25, inner_w * 0.75];
|
||||
rear_boss = 9; // rear corner boss block size
|
||||
boss_h = 10; // body boss height before the chamfer
|
||||
rear_screws = [[rear_boss / 2, depth - wall - rear_boss / 2],
|
||||
[inner_w - rear_boss / 2, depth - wall - rear_boss / 2]];
|
||||
base_screws = concat([for (x = foot_xs) [x, foot_y]], rear_screws);
|
||||
// front side bosses: far enough back that the display's back stays clear while
|
||||
// the bezel slides in along the panel
|
||||
n_disp_back = n_pcb + pcb_t + disp_back;
|
||||
front_boss_y = ceil((n_disp_back + 2 + (boss_h + rear_boss) * sin(tilt)) / cos(tilt));
|
||||
front_screws = [[rear_boss / 2, front_boss_y + rear_boss / 2],
|
||||
[inner_w - rear_boss / 2, front_boss_y + rear_boss / 2]];
|
||||
body_screws = concat(front_screws, rear_screws);
|
||||
base_screws = concat([for (x = foot_xs) [x, foot_y]], body_screws);
|
||||
|
||||
echo(str("Outer size: ", outer_w, " x ", depth, " x ", height + base_t, " mm (W x D x H)"));
|
||||
|
||||
@@ -151,20 +159,24 @@ module body() {
|
||||
for (i = [0 : 3]) translate([inner_w / 2, depth - wall - 14 - i * 8, height - wall / 2])
|
||||
linear_extrude(wall + 2, center = true) rrect(inner_w - 50, 3, 1.4);
|
||||
}
|
||||
// rear corner bosses for the base screws, chamfered up into the walls
|
||||
for (p = rear_screws) {
|
||||
// bosses for the base screws, chamfered up into the walls
|
||||
for (p = rear_screws) body_boss(p, true);
|
||||
for (p = front_screws) body_boss(p, false);
|
||||
}
|
||||
|
||||
// rear: in the corner, chamfered into the side and back walls; front: side wall only
|
||||
module body_boss(p, rear) {
|
||||
x0 = p[0] < inner_w / 2 ? 0 : inner_w - rear_boss;
|
||||
xw = p[0] < inner_w / 2 ? 0 : inner_w - 0.01;
|
||||
y0 = p[1] - rear_boss / 2;
|
||||
difference() {
|
||||
hull() {
|
||||
translate([x0, depth - wall - rear_boss, 0]) cube([rear_boss, rear_boss, 10]);
|
||||
translate([xw, depth - wall - 0.01, 0]) cube([0.01, 0.01, 10 + rear_boss]);
|
||||
translate([x0, depth - wall - 0.01, 0]) cube([rear_boss, 0.01, 10 + rear_boss]);
|
||||
translate([xw, depth - wall - rear_boss, 0]) cube([0.01, rear_boss, 10 + rear_boss]);
|
||||
translate([x0, y0, 0]) cube([rear_boss, rear_boss, boss_h]);
|
||||
translate([xw, y0, 0]) cube([0.01, rear_boss, boss_h + rear_boss]);
|
||||
if (rear) translate([x0, y0 + rear_boss - 0.01, 0]) cube([rear_boss, 0.01, boss_h + rear_boss]);
|
||||
}
|
||||
translate([p[0], p[1], -1]) cylinder(d = insert_d, h = insert_depth + 1);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
// ---------- bezel ----------
|
||||
@@ -210,8 +222,12 @@ module base() {
|
||||
translate([-wall, 0, -base_t]) cube([outer_w, depth, base_t]);
|
||||
// locating rim inside the side and back walls (stops short of the bezel and bosses)
|
||||
rim_y0 = 20;
|
||||
difference() {
|
||||
for (x = [clr, inner_w - clr - 1.6])
|
||||
translate([x, rim_y0, -0.01]) cube([1.6, depth - wall - rear_boss - clr - rim_y0, 2]);
|
||||
for (p = front_screws) translate([p[0], p[1], 1])
|
||||
cube([rear_boss + 2 * clr, rear_boss + 2 * clr, 4], center = true);
|
||||
}
|
||||
translate([rear_boss + clr, depth - wall - clr - 1.6, -0.01])
|
||||
cube([inner_w - 2 * (rear_boss + clr), 1.6, 2]);
|
||||
// board standoffs
|
||||
@@ -314,7 +330,7 @@ if (part == "assembly") {
|
||||
} else if (part == "bezel") {
|
||||
translate([0, 0, -lip]) multmatrix(M) bezel(); // front face on the bed
|
||||
} else if (part == "feet") {
|
||||
for (i = [0 : len(base_screws) - 1]) // 4 feet, flat side down
|
||||
for (i = [0 : len(base_screws) - 1]) // 6 feet, flat side down
|
||||
translate([i * (foot_d + 5), 0, foot_h]) foot();
|
||||
} else if (part == "base") {
|
||||
translate([0, 0, base_t]) base();
|
||||
|
||||
@@ -4,11 +4,11 @@
|
||||
# your secrets.yaml), or use it as a reference for your own device config.
|
||||
#
|
||||
# Wiring (3-pin connector on the display, 9600 8N1):
|
||||
# pin 1 VCC <- 5-24V supply, up to 1.2A at 5V (not the ESP32 regulator)
|
||||
# pin 2 RXD <- MAX3232 T1OUT <- T1IN <- ESP32 GPIO17 (TX)
|
||||
# pin 3 GND <-> supply GND, MAX3232 GND and ESP32 GND
|
||||
# pin 1 VCC <- 5-24V supply, up to 1.2A at 5V (not the D1's regulator)
|
||||
# pin 2 RXD <- MAX3232 T1OUT <- T1IN <- WEMOS D1 R1 GPIO2 / D9 (UART1 TX)
|
||||
# pin 3 GND <-> supply GND, MAX3232 GND and D1 GND
|
||||
#
|
||||
# RXD is an RS-232 input. Without a MAX3232, wire GPIO17 straight to RXD and
|
||||
# RXD is an RS-232 input. Without a MAX3232, wire GPIO2 straight to RXD and
|
||||
# set `inverted: true` under uart.
|
||||
|
||||
esphome:
|
||||
@@ -42,10 +42,9 @@ external_components:
|
||||
# type: local
|
||||
# path: ../components
|
||||
|
||||
esp32:
|
||||
board: esp32dev
|
||||
framework:
|
||||
type: arduino
|
||||
# WEMOS D1 R1 (UNO-sized ESP8266 board).
|
||||
esp8266:
|
||||
board: d1
|
||||
|
||||
logger:
|
||||
level: INFO
|
||||
@@ -85,7 +84,7 @@ time:
|
||||
uart:
|
||||
id: uart_vfd
|
||||
tx_pin:
|
||||
number: GPIO17
|
||||
number: GPIO2 # UART1, TX-only; UART0 stays free for the USB logger
|
||||
inverted: false # true when wired directly, without a MAX3232
|
||||
baud_rate: 9600
|
||||
parity: NONE
|
||||
|
||||
Reference in new issue
Block a user