Compare commits

..
3 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 bd773982f8 Case: add TPU feet held by the base screws
Each foot has a spigot that locates in the base's screw counterbore and a
pocket for the screw head; base screws become M3x10. Base unchanged.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:06:07 +01:00
mangavalkandClaude Opus 5.5 bf17b9c0ba Case README: keep measurement list together
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:04:01 +01:00
mangavalkandClaude Opus 5.5 02f8289852 Case: mount the display the right way up
The glass is 4.4 mm off-centre on the display PCB. Turning the display
180 degrees so the text reads correctly moved the glass partly behind the
window edge. New disp_rotated option (default on) moves the bezel bosses
to match. Only the bezel changes.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-01 13:03:53 +01:00
4 changed files with 57 additions and 8 deletions

No files matched your search

+12 -3
View File
@@ -20,6 +20,7 @@ at least 210 × 115 mm.
| [stl/body.stl](stl/body.stl) | upside down, top on the bed (as exported) | Sides, top and back wall. No supports needed. |
| [stl/bezel.stl](stl/bezel.stl) | face down (as exported) | Front panel with the window and the display bosses. |
| [stl/base.stl](stl/base.stl) | flat (as exported) | Floor with the board standoffs and the screw holes. |
| [stl/feet.stl](stl/feet.stl) | flat side down (as exported) | 4 feet, print in **TPU**. Each clamps under one of the base screws, with a spigot that locates in the screw's counterbore. |
PETG is a good choice: the display warms the inside by a few degrees. PLA
works if the case stays out of the sun.
@@ -34,7 +35,7 @@ works if the case stays out of the sun.
- 4 on the base's board standoffs
- 4 × M3×8 to bolt the display to the bezel
- 4 × M3×6 to hold the D1 board on its standoffs
- 4 × M3×8 to hold the base on, from below
- 4 × M3×8 to hold the base on, from below; **M3×10** with the TPU feet
## Assembly
@@ -46,7 +47,9 @@ works if the case stays out of the sun.
5. Connect the display cable. The MAX3232 sits inline in the cable; tie it to
the anchor on the base.
6. Put the body on the base and screw it together from below. The base holds
the bezel in place.
the bezel in place. With the feet, put a foot on each screw first (the
spigot faces the base) and use M3×10. Tighten until the foot is snug; the
TPU only needs light compression.
## Measure before printing
@@ -60,6 +63,11 @@ check these against yours and change the values at the top of
position and the distance from its front face to the PCB.
- `usb_pos`: where the micro-USB port is along the D1's back edge (38 mm from
the jack side is a guess based on the UNO layout). Also check `jack_pos`.
- `disp_rotated`: the glass is off-centre on the display's PCB, so the bezel
depends on which way up the display is mounted. `true` (the default) is the
orientation the display reads correctly in: turned 180° from the
datasheet's front view, with the jumper header on the left seen from the
front.
If only the display is off, it's enough to reprint the bezel.
@@ -73,6 +81,7 @@ with:
openscad -D 'part="body"' --export-format binstl -o stl/body.stl vfd-case.scad
openscad -D 'part="bezel"' --export-format binstl -o stl/bezel.stl vfd-case.scad
openscad -D 'part="base"' --export-format binstl -o stl/base.stl vfd-case.scad
openscad -D 'part="feet"' --export-format binstl -o stl/feet.stl vfd-case.scad
```
`part="assembly"` shows everything with dummy display and board models, and
@@ -80,7 +89,7 @@ openscad -D 'part="base"' --export-format binstl -o stl/base.stl vfd-case.scad
each one must render as an empty object:
- `check_body_bezel`, `check_body_display`, `check_bezel_display`
- `check_body_base`, `check_bezel_base`, `check_display_base`
- `check_body_base`, `check_bezel_base`, `check_display_base`, `check_feet_base`
- `check_board`
- `check_insertion`: sweeps the bezel and display along their slide-in path
through the body.
Binary file not shown.
BIN
View File
Binary file not shown.
+45 -5
View File
@@ -35,8 +35,8 @@ top_margin = 4; // bezel above the display's top edge (along the panel)
disp_w = 190;
disp_h = 64;
disp_hole_inset = 4; // hole centres from the PCB edges (182 x 56 spacing)
glass_x0 = 3.0; // glass left edge from PCB left edge (front view)
glass_y0 = 7.85; // glass bottom edge from PCB bottom edge
glass_x0 = 3.0; // glass left edge from PCB left edge (datasheet front view)
glass_y0 = 7.85; // glass bottom edge from PCB bottom edge (datasheet front view)
glass_w = 175.2;
glass_h = 48.3;
glass_depth = 12.0; // glass front face to PCB front face
@@ -44,6 +44,9 @@ glass_gap = 0.5; // air gap between bezel and glass (datasheet asks for o
pcb_t = 1.6;
disp_back = 11; // components behind the display PCB
disp_raise = 14; // PCB bottom edge, measured along the panel from the bottom
disp_rotated = true; // display turned 180 deg from the datasheet's front view
// (jumper header on the left seen from the front); the
// glass is off-centre, so this moves the bosses 8.8 mm
/* [Window] */
win_w = 156;
@@ -59,6 +62,14 @@ screw_d = 3.4; // M3 clearance
head_d = 6.2; // M3 head counterbore in the base
head_depth = 2;
/* [TPU feet, held by the base screws (use M3x10 instead of M3x8)] */
foot_d = 14; // fits inside the base outline at the rear corners
foot_h = 4.5; // below the base
foot_spigot_h = 1.8; // locates in the base's screw counterbore
foot_spigot_d = head_d - 0.2;
foot_head_d = 6.6; // pocket for the screw head (from below)
foot_head_depth = 3.5; // M3 socket head is 3 mm tall
/* [WEMOS D1 R1 (Arduino UNO footprint)] */
board_l = 68.58; // along the case depth, connector edge at the back
board_w = 53.34;
@@ -76,7 +87,10 @@ board_comp_h = 10; // tallest part on the board (dummy for the collision ch
$fn = 48;
// ---------- derived ----------
gx_c = glass_x0 + glass_w / 2; // glass centre from PCB left
// glass position from the PCB's bottom-left corner as mounted (front view)
gl_x = disp_rotated ? disp_w - glass_x0 - glass_w : glass_x0;
gl_y = disp_rotated ? disp_h - glass_y0 - glass_h : glass_y0;
gx_c = gl_x + glass_w / 2; // glass centre from PCB left
inner_w = 2 * (max(gx_c, disp_w - gx_c) + 1.5); // window centred, 1.5 mm side clearance
outer_w = inner_w + 2 * wall;
disp_x0 = inner_w / 2 - gx_c; // PCB left edge, x
@@ -85,7 +99,7 @@ height = z_top_in + wall;
n_bezel_in = lip + bezel_t; // bezel inner face (local N)
n_glass = n_bezel_in + glass_gap;
n_pcb = n_glass + glass_depth;
win_s = disp_raise + glass_y0 + glass_h / 2; // window centre along the panel
win_s = disp_raise + gl_y + glass_h / 2; // window centre along the panel
board_x0 = inner_w / 2 - board_w / 2;
board_conn_y = depth - wall - board_gap; // y of the board's connector edge
pcb_top_z = standoff_h + pcb_t;
@@ -221,6 +235,27 @@ module base() {
function board_xy(h) = [board_x0 + h[1], board_conn_y - h[0], 0];
// One foot, top face at z = 0 (against the base's underside), centred on a screw.
module foot() {
difference() {
union() {
translate([0, 0, -foot_h]) cylinder(d = foot_d, h = foot_h);
translate([0, 0, -0.01]) cylinder(d = foot_spigot_d, h = foot_spigot_h + 0.01);
}
translate([0, 0, -foot_h - 1]) cylinder(d = screw_d, h = foot_h + foot_spigot_h + 2);
translate([0, 0, -foot_h - 1]) cylinder(d = foot_head_d, h = foot_head_depth + 1);
// soften the bottom edge
translate([0, 0, -foot_h - 0.01]) difference() {
cylinder(d = foot_d + 1, h = 1);
cylinder(d1 = foot_d - 2, d2 = foot_d + 0.01, h = 1.01);
}
}
}
module feet_in_place() {
for (p = base_screws) translate([p[0], p[1], -base_t]) foot();
}
module tie_anchor() {
difference() {
translate([-5, -3, 0]) cube([10, 6, 5]);
@@ -231,7 +266,7 @@ module tie_anchor() {
// ---------- dummies for the preview and the collision checks ----------
module display_dummy() {
panel() {
translate([disp_x0 + glass_x0, disp_raise + glass_y0, n_glass + 0.01])
translate([disp_x0 + gl_x, disp_raise + gl_y, n_glass + 0.01])
cube([glass_w, glass_h, glass_depth - 0.02]);
translate([disp_x0, disp_raise, n_pcb + 0.01]) difference() {
cube([disp_w, disp_h, pcb_t + disp_back]);
@@ -259,6 +294,7 @@ if (part == "assembly") {
color("SlateGray", 0.5) body();
color("DimGray") bezel();
color("Gainsboro") base();
color("Black") feet_in_place();
color("SeaGreen") display_dummy();
color("SteelBlue") board_dummy();
} else if (part == "section") {
@@ -277,6 +313,9 @@ if (part == "assembly") {
translate([0, depth, height]) rotate([180, 0, 0]) body(); // top on the bed
} else if (part == "bezel") {
translate([0, 0, -lip]) multmatrix(M) bezel(); // front face on the bed
} else if (part == "feet") {
for (i = [0 : len(base_screws) - 1]) // 4 feet, flat side down
translate([i * (foot_d + 5), 0, foot_h]) foot();
} else if (part == "base") {
translate([0, 0, base_t]) base();
}
@@ -288,6 +327,7 @@ else if (part == "check_body_base") intersection() { body(); base(); }
else if (part == "check_bezel_base") intersection() { bezel(); base(); }
else if (part == "check_board") intersection() { union() { body(); bezel(); base(); display_dummy(); } board_dummy(); }
else if (part == "check_display_base") intersection() { base(); display_dummy(); }
else if (part == "check_feet_base") intersection() { base(); feet_in_place(); }
// The bezel slides in from below along the panel: sweep it (with the display) down and check.
else if (part == "check_insertion") intersection() {
body();