Compare commits
3
Commits
17d0c1be3b
...
bd773982f8
| Author | SHA1 | Date | |
|---|---|---|---|
|
|
bd773982f8 | ||
|
|
bf17b9c0ba | ||
|
|
02f8289852 |
No files matched your search
+12
-3
@@ -20,6 +20,7 @@ at least 210 × 115 mm.
|
|||||||
| [stl/body.stl](stl/body.stl) | upside down, top on the bed (as exported) | Sides, top and back wall. No supports needed. |
|
| [stl/body.stl](stl/body.stl) | upside down, top on the bed (as exported) | Sides, top and back wall. No supports needed. |
|
||||||
| [stl/bezel.stl](stl/bezel.stl) | face down (as exported) | Front panel with the window and the display bosses. |
|
| [stl/bezel.stl](stl/bezel.stl) | face down (as exported) | Front panel with the window and the display bosses. |
|
||||||
| [stl/base.stl](stl/base.stl) | flat (as exported) | Floor with the board standoffs and the screw holes. |
|
| [stl/base.stl](stl/base.stl) | flat (as exported) | Floor with the board standoffs and the screw holes. |
|
||||||
|
| [stl/feet.stl](stl/feet.stl) | flat side down (as exported) | 4 feet, print in **TPU**. Each clamps under one of the base screws, with a spigot that locates in the screw's counterbore. |
|
||||||
|
|
||||||
PETG is a good choice: the display warms the inside by a few degrees. PLA
|
PETG is a good choice: the display warms the inside by a few degrees. PLA
|
||||||
works if the case stays out of the sun.
|
works if the case stays out of the sun.
|
||||||
@@ -34,7 +35,7 @@ works if the case stays out of the sun.
|
|||||||
- 4 on the base's board standoffs
|
- 4 on the base's board standoffs
|
||||||
- 4 × M3×8 to bolt the display to the bezel
|
- 4 × M3×8 to bolt the display to the bezel
|
||||||
- 4 × M3×6 to hold the D1 board on its standoffs
|
- 4 × M3×6 to hold the D1 board on its standoffs
|
||||||
- 4 × M3×8 to hold the base on, from below
|
- 4 × M3×8 to hold the base on, from below; **M3×10** with the TPU feet
|
||||||
|
|
||||||
## Assembly
|
## Assembly
|
||||||
|
|
||||||
@@ -46,7 +47,9 @@ works if the case stays out of the sun.
|
|||||||
5. Connect the display cable. The MAX3232 sits inline in the cable; tie it to
|
5. Connect the display cable. The MAX3232 sits inline in the cable; tie it to
|
||||||
the anchor on the base.
|
the anchor on the base.
|
||||||
6. Put the body on the base and screw it together from below. The base holds
|
6. Put the body on the base and screw it together from below. The base holds
|
||||||
the bezel in place.
|
the bezel in place. With the feet, put a foot on each screw first (the
|
||||||
|
spigot faces the base) and use M3×10. Tighten until the foot is snug; the
|
||||||
|
TPU only needs light compression.
|
||||||
|
|
||||||
## Measure before printing
|
## Measure before printing
|
||||||
|
|
||||||
@@ -60,6 +63,11 @@ check these against yours and change the values at the top of
|
|||||||
position and the distance from its front face to the PCB.
|
position and the distance from its front face to the PCB.
|
||||||
- `usb_pos`: where the micro-USB port is along the D1's back edge (38 mm from
|
- `usb_pos`: where the micro-USB port is along the D1's back edge (38 mm from
|
||||||
the jack side is a guess based on the UNO layout). Also check `jack_pos`.
|
the jack side is a guess based on the UNO layout). Also check `jack_pos`.
|
||||||
|
- `disp_rotated`: the glass is off-centre on the display's PCB, so the bezel
|
||||||
|
depends on which way up the display is mounted. `true` (the default) is the
|
||||||
|
orientation the display reads correctly in: turned 180° from the
|
||||||
|
datasheet's front view, with the jumper header on the left seen from the
|
||||||
|
front.
|
||||||
|
|
||||||
If only the display is off, it's enough to reprint the bezel.
|
If only the display is off, it's enough to reprint the bezel.
|
||||||
|
|
||||||
@@ -73,6 +81,7 @@ with:
|
|||||||
openscad -D 'part="body"' --export-format binstl -o stl/body.stl vfd-case.scad
|
openscad -D 'part="body"' --export-format binstl -o stl/body.stl vfd-case.scad
|
||||||
openscad -D 'part="bezel"' --export-format binstl -o stl/bezel.stl vfd-case.scad
|
openscad -D 'part="bezel"' --export-format binstl -o stl/bezel.stl vfd-case.scad
|
||||||
openscad -D 'part="base"' --export-format binstl -o stl/base.stl vfd-case.scad
|
openscad -D 'part="base"' --export-format binstl -o stl/base.stl vfd-case.scad
|
||||||
|
openscad -D 'part="feet"' --export-format binstl -o stl/feet.stl vfd-case.scad
|
||||||
```
|
```
|
||||||
|
|
||||||
`part="assembly"` shows everything with dummy display and board models, and
|
`part="assembly"` shows everything with dummy display and board models, and
|
||||||
@@ -80,7 +89,7 @@ openscad -D 'part="base"' --export-format binstl -o stl/base.stl vfd-case.scad
|
|||||||
each one must render as an empty object:
|
each one must render as an empty object:
|
||||||
|
|
||||||
- `check_body_bezel`, `check_body_display`, `check_bezel_display`
|
- `check_body_bezel`, `check_body_display`, `check_bezel_display`
|
||||||
- `check_body_base`, `check_bezel_base`, `check_display_base`
|
- `check_body_base`, `check_bezel_base`, `check_display_base`, `check_feet_base`
|
||||||
- `check_board`
|
- `check_board`
|
||||||
- `check_insertion`: sweeps the bezel and display along their slide-in path
|
- `check_insertion`: sweeps the bezel and display along their slide-in path
|
||||||
through the body.
|
through the body.
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
+45
-5
@@ -35,8 +35,8 @@ top_margin = 4; // bezel above the display's top edge (along the panel)
|
|||||||
disp_w = 190;
|
disp_w = 190;
|
||||||
disp_h = 64;
|
disp_h = 64;
|
||||||
disp_hole_inset = 4; // hole centres from the PCB edges (182 x 56 spacing)
|
disp_hole_inset = 4; // hole centres from the PCB edges (182 x 56 spacing)
|
||||||
glass_x0 = 3.0; // glass left edge from PCB left edge (front view)
|
glass_x0 = 3.0; // glass left edge from PCB left edge (datasheet front view)
|
||||||
glass_y0 = 7.85; // glass bottom edge from PCB bottom edge
|
glass_y0 = 7.85; // glass bottom edge from PCB bottom edge (datasheet front view)
|
||||||
glass_w = 175.2;
|
glass_w = 175.2;
|
||||||
glass_h = 48.3;
|
glass_h = 48.3;
|
||||||
glass_depth = 12.0; // glass front face to PCB front face
|
glass_depth = 12.0; // glass front face to PCB front face
|
||||||
@@ -44,6 +44,9 @@ glass_gap = 0.5; // air gap between bezel and glass (datasheet asks for o
|
|||||||
pcb_t = 1.6;
|
pcb_t = 1.6;
|
||||||
disp_back = 11; // components behind the display PCB
|
disp_back = 11; // components behind the display PCB
|
||||||
disp_raise = 14; // PCB bottom edge, measured along the panel from the bottom
|
disp_raise = 14; // PCB bottom edge, measured along the panel from the bottom
|
||||||
|
disp_rotated = true; // display turned 180 deg from the datasheet's front view
|
||||||
|
// (jumper header on the left seen from the front); the
|
||||||
|
// glass is off-centre, so this moves the bosses 8.8 mm
|
||||||
|
|
||||||
/* [Window] */
|
/* [Window] */
|
||||||
win_w = 156;
|
win_w = 156;
|
||||||
@@ -59,6 +62,14 @@ screw_d = 3.4; // M3 clearance
|
|||||||
head_d = 6.2; // M3 head counterbore in the base
|
head_d = 6.2; // M3 head counterbore in the base
|
||||||
head_depth = 2;
|
head_depth = 2;
|
||||||
|
|
||||||
|
/* [TPU feet, held by the base screws (use M3x10 instead of M3x8)] */
|
||||||
|
foot_d = 14; // fits inside the base outline at the rear corners
|
||||||
|
foot_h = 4.5; // below the base
|
||||||
|
foot_spigot_h = 1.8; // locates in the base's screw counterbore
|
||||||
|
foot_spigot_d = head_d - 0.2;
|
||||||
|
foot_head_d = 6.6; // pocket for the screw head (from below)
|
||||||
|
foot_head_depth = 3.5; // M3 socket head is 3 mm tall
|
||||||
|
|
||||||
/* [WEMOS D1 R1 (Arduino UNO footprint)] */
|
/* [WEMOS D1 R1 (Arduino UNO footprint)] */
|
||||||
board_l = 68.58; // along the case depth, connector edge at the back
|
board_l = 68.58; // along the case depth, connector edge at the back
|
||||||
board_w = 53.34;
|
board_w = 53.34;
|
||||||
@@ -76,7 +87,10 @@ board_comp_h = 10; // tallest part on the board (dummy for the collision ch
|
|||||||
$fn = 48;
|
$fn = 48;
|
||||||
|
|
||||||
// ---------- derived ----------
|
// ---------- derived ----------
|
||||||
gx_c = glass_x0 + glass_w / 2; // glass centre from PCB left
|
// glass position from the PCB's bottom-left corner as mounted (front view)
|
||||||
|
gl_x = disp_rotated ? disp_w - glass_x0 - glass_w : glass_x0;
|
||||||
|
gl_y = disp_rotated ? disp_h - glass_y0 - glass_h : glass_y0;
|
||||||
|
gx_c = gl_x + glass_w / 2; // glass centre from PCB left
|
||||||
inner_w = 2 * (max(gx_c, disp_w - gx_c) + 1.5); // window centred, 1.5 mm side clearance
|
inner_w = 2 * (max(gx_c, disp_w - gx_c) + 1.5); // window centred, 1.5 mm side clearance
|
||||||
outer_w = inner_w + 2 * wall;
|
outer_w = inner_w + 2 * wall;
|
||||||
disp_x0 = inner_w / 2 - gx_c; // PCB left edge, x
|
disp_x0 = inner_w / 2 - gx_c; // PCB left edge, x
|
||||||
@@ -85,7 +99,7 @@ height = z_top_in + wall;
|
|||||||
n_bezel_in = lip + bezel_t; // bezel inner face (local N)
|
n_bezel_in = lip + bezel_t; // bezel inner face (local N)
|
||||||
n_glass = n_bezel_in + glass_gap;
|
n_glass = n_bezel_in + glass_gap;
|
||||||
n_pcb = n_glass + glass_depth;
|
n_pcb = n_glass + glass_depth;
|
||||||
win_s = disp_raise + glass_y0 + glass_h / 2; // window centre along the panel
|
win_s = disp_raise + gl_y + glass_h / 2; // window centre along the panel
|
||||||
board_x0 = inner_w / 2 - board_w / 2;
|
board_x0 = inner_w / 2 - board_w / 2;
|
||||||
board_conn_y = depth - wall - board_gap; // y of the board's connector edge
|
board_conn_y = depth - wall - board_gap; // y of the board's connector edge
|
||||||
pcb_top_z = standoff_h + pcb_t;
|
pcb_top_z = standoff_h + pcb_t;
|
||||||
@@ -221,6 +235,27 @@ module base() {
|
|||||||
|
|
||||||
function board_xy(h) = [board_x0 + h[1], board_conn_y - h[0], 0];
|
function board_xy(h) = [board_x0 + h[1], board_conn_y - h[0], 0];
|
||||||
|
|
||||||
|
// One foot, top face at z = 0 (against the base's underside), centred on a screw.
|
||||||
|
module foot() {
|
||||||
|
difference() {
|
||||||
|
union() {
|
||||||
|
translate([0, 0, -foot_h]) cylinder(d = foot_d, h = foot_h);
|
||||||
|
translate([0, 0, -0.01]) cylinder(d = foot_spigot_d, h = foot_spigot_h + 0.01);
|
||||||
|
}
|
||||||
|
translate([0, 0, -foot_h - 1]) cylinder(d = screw_d, h = foot_h + foot_spigot_h + 2);
|
||||||
|
translate([0, 0, -foot_h - 1]) cylinder(d = foot_head_d, h = foot_head_depth + 1);
|
||||||
|
// soften the bottom edge
|
||||||
|
translate([0, 0, -foot_h - 0.01]) difference() {
|
||||||
|
cylinder(d = foot_d + 1, h = 1);
|
||||||
|
cylinder(d1 = foot_d - 2, d2 = foot_d + 0.01, h = 1.01);
|
||||||
|
}
|
||||||
|
}
|
||||||
|
}
|
||||||
|
|
||||||
|
module feet_in_place() {
|
||||||
|
for (p = base_screws) translate([p[0], p[1], -base_t]) foot();
|
||||||
|
}
|
||||||
|
|
||||||
module tie_anchor() {
|
module tie_anchor() {
|
||||||
difference() {
|
difference() {
|
||||||
translate([-5, -3, 0]) cube([10, 6, 5]);
|
translate([-5, -3, 0]) cube([10, 6, 5]);
|
||||||
@@ -231,7 +266,7 @@ module tie_anchor() {
|
|||||||
// ---------- dummies for the preview and the collision checks ----------
|
// ---------- dummies for the preview and the collision checks ----------
|
||||||
module display_dummy() {
|
module display_dummy() {
|
||||||
panel() {
|
panel() {
|
||||||
translate([disp_x0 + glass_x0, disp_raise + glass_y0, n_glass + 0.01])
|
translate([disp_x0 + gl_x, disp_raise + gl_y, n_glass + 0.01])
|
||||||
cube([glass_w, glass_h, glass_depth - 0.02]);
|
cube([glass_w, glass_h, glass_depth - 0.02]);
|
||||||
translate([disp_x0, disp_raise, n_pcb + 0.01]) difference() {
|
translate([disp_x0, disp_raise, n_pcb + 0.01]) difference() {
|
||||||
cube([disp_w, disp_h, pcb_t + disp_back]);
|
cube([disp_w, disp_h, pcb_t + disp_back]);
|
||||||
@@ -259,6 +294,7 @@ if (part == "assembly") {
|
|||||||
color("SlateGray", 0.5) body();
|
color("SlateGray", 0.5) body();
|
||||||
color("DimGray") bezel();
|
color("DimGray") bezel();
|
||||||
color("Gainsboro") base();
|
color("Gainsboro") base();
|
||||||
|
color("Black") feet_in_place();
|
||||||
color("SeaGreen") display_dummy();
|
color("SeaGreen") display_dummy();
|
||||||
color("SteelBlue") board_dummy();
|
color("SteelBlue") board_dummy();
|
||||||
} else if (part == "section") {
|
} else if (part == "section") {
|
||||||
@@ -277,6 +313,9 @@ if (part == "assembly") {
|
|||||||
translate([0, depth, height]) rotate([180, 0, 0]) body(); // top on the bed
|
translate([0, depth, height]) rotate([180, 0, 0]) body(); // top on the bed
|
||||||
} else if (part == "bezel") {
|
} else if (part == "bezel") {
|
||||||
translate([0, 0, -lip]) multmatrix(M) bezel(); // front face on the bed
|
translate([0, 0, -lip]) multmatrix(M) bezel(); // front face on the bed
|
||||||
|
} else if (part == "feet") {
|
||||||
|
for (i = [0 : len(base_screws) - 1]) // 4 feet, flat side down
|
||||||
|
translate([i * (foot_d + 5), 0, foot_h]) foot();
|
||||||
} else if (part == "base") {
|
} else if (part == "base") {
|
||||||
translate([0, 0, base_t]) base();
|
translate([0, 0, base_t]) base();
|
||||||
}
|
}
|
||||||
@@ -288,6 +327,7 @@ else if (part == "check_body_base") intersection() { body(); base(); }
|
|||||||
else if (part == "check_bezel_base") intersection() { bezel(); base(); }
|
else if (part == "check_bezel_base") intersection() { bezel(); base(); }
|
||||||
else if (part == "check_board") intersection() { union() { body(); bezel(); base(); display_dummy(); } board_dummy(); }
|
else if (part == "check_board") intersection() { union() { body(); bezel(); base(); display_dummy(); } board_dummy(); }
|
||||||
else if (part == "check_display_base") intersection() { base(); display_dummy(); }
|
else if (part == "check_display_base") intersection() { base(); display_dummy(); }
|
||||||
|
else if (part == "check_feet_base") intersection() { base(); feet_in_place(); }
|
||||||
// The bezel slides in from below along the panel: sweep it (with the display) down and check.
|
// The bezel slides in from below along the panel: sweep it (with the display) down and check.
|
||||||
else if (part == "check_insertion") intersection() {
|
else if (part == "check_insertion") intersection() {
|
||||||
body();
|
body();
|
||||||
|
|||||||
Reference in new issue
Block a user