41 lines
2.3 KiB
Markdown
41 lines
2.3 KiB
Markdown
 
|
# Plasma DMD
|
|||
|
|
|
|||
|
|
Drive a second-hand 128×32 pinball **plasma** dot-matrix display (originally on a Williams WPC
|
|||
|
|
DMD controller) standalone, from a **Wemos D1 mini ESP32**, powered from a single **12 V DC** brick.
|
|||
|
|
|
|||
|
|
The display power supply is built from cheap modules plus a copy of the regulator section of the
|
|||
|
|
Stern/Sega display PSU (520-5138-00). The original transformer and AC front end are not used.
|
|||
|
|
|
|||
|
|
> ⚠️ **High voltage.** The panel runs on about +65 V, −100 V and −112 V, which is about 175 V
|
|||
|
|
> between rails. That can injure you. Read [docs/safety.md](docs/safety.md) before powering anything.
|
|||
|
|
|
|||
|
|
## The panel
|
|||
|
|
|
|||
|
|
- Bought second-hand on 18 September 2021 for €37.
|
|||
|
|
- Originally driven by a Williams WPC DMD controller board. No original controller or PSU came with it.
|
|||
|
|
|
|||
|
|
## Layout
|
|||
|
|
|
|||
|
|
| Path | Contents |
|
|||
|
|
|---|---|
|
|||
|
|
| [docs/power-supply.md](docs/power-supply.md) | PSU design: block diagram, analysis of the original board, changes |
|
|||
|
|
| [hardware/psu-schematic.svg](hardware/psu-schematic.svg) | PSU schematic (generated by [hardware/psu_schematic.py](hardware/psu_schematic.py)) |
|
|||
|
|
| [hardware/kicad/](hardware/kicad/) | KiCad 10 project for the PSU carrier board (schematic + net classes, PCB not started) |
|
|||
|
|
| [docs/safety.md](docs/safety.md) | Safety design (HV watchdog, fusing, layout, bring-up procedure) |
|
|||
|
|
| [docs/esp32-interface.md](docs/esp32-interface.md) | ESP32 pin plan, 74HCT245 level shifter, panel signals |
|
|||
|
|
| [docs/bom.md](docs/bom.md) | Bill of materials |
|
|||
|
|
| [reference/](reference/) | Original Stern 520-5138-00 display PSU schematic |
|
|||
|
|
| [firmware/](firmware/) | PlatformIO project for the ESP32 |
|
|||
|
|
|
|||
|
|
## Status
|
|||
|
|
|
|||
|
|
- [ ] Identify panel: manufacturer/part number from its label
|
|||
|
|
- [ ] Map the panel's power connector pins (WPC panel ≠ Stern CN2 pinout) and check if +12 V is used
|
|||
|
|
- [ ] Map the panel's 14-pin data connector
|
|||
|
|
- [ ] Lay out the PSU PCB in KiCad ([hardware/kicad/](hardware/kicad/README.md))
|
|||
|
|
- [ ] Order parts ([docs/bom.md](docs/bom.md))
|
|||
|
|
- [ ] Build and bench-test the PSU **without the panel** ([bring-up](docs/safety.md#bring-up-procedure))
|
|||
|
|
- [ ] Build HV watchdog and verify that the relay drops when toggling stops
|
|||
|
|
- [ ] Firmware: row scanning with test pattern
|
|||
|
|
- [ ] First power-up with panel (series resistors, current measurement)
|
|||
|
|
- [ ] Firmware: greyscale, content source (Wi-Fi / serial)
|