// Dashboard holder for the JC3636W518 round display (12-OBD-Speed) // // Three printed parts + M3x20 bolt + M3 nut + VHB tape: // cup - snap-in holder for the 58 x 11 mm puck, hinge knuckle at its bottom edge // base - flat foot (VHB tape) with two hinge ears, captive M3 nut in the right ear // knob - thumb knob that holds the M3 bolt head // // Angle adjustment: the knuckle and both ears carry radial face teeth (detents). // Loosen the knob ~1 turn -> the ears spring apart and the cup turns freely, // set the angle, tighten -> the teeth lock (360/teeth degrees per step). // // Print in ASA (dashboard heat). Orientation is already correct for every part: // cup : back on the bed (lip up) base : foot on the bed knob : flat on the bed // // Set `part` to "cup", "base" or "knob" and export each STL (F6, then F7). part = "assembly"; // [assembly, cup, base, knob, print] tilt = 30; // assembly preview only: lean back from vertical (deg) /* [Puck] */ puck_d = 58.0; // metal case diameter puck_h = 11.0; // case thickness glass_d = 55.0; // cover glass diameter (lip must stay outside it) /* [Cup] */ fit = 0.3; // diametral clearance puck <-> cup wall_t = 2.0; // cup side wall floor_t = 2.0; // cup back lip = 0.9; // how far the snap lip reaches over the bezel (radial) lip_t = 1.2; // lip thickness push_d = 36; // hole in the back to push the puck out (0 = none) slots = 8; // flex slots in the wall (make the snap easier) slot_w = 1.2; usb_angle = 0; // USB-C opening: 0 = right, 180 = left (seen from the front) usb_w = 13; // opening width (USB-C plug overmold ~12 mm) /* [Hinge] */ teeth = 36; // detent teeth -> 360/teeth degrees per click tooth_h = 0.6; // tooth height tooth_r_in = 5.0; // inner radius of the tooth ring hinge_r = 9.0; // knuckle / ear disc radius (= outer radius of the teeth) knuckle_w = 8.0; // knuckle width (between the ears) ear_t = 4.0; // ear thickness ear_spread = 0.8; // extra gap per side as printed, so the teeth clear when loose bolt_d = 3.4; // M3 clearance hole nut_af = 5.7; // M3 nut across flats + clearance nut_h = 2.6; // nut pocket depth /* [Base] */ foot_w = 40; // across the car (x) foot_l = 46; // front-back (y) foot_t = 4; foot_r = 6; // corner radius /* [Knob] */ knob_d = 20; knob_floor = 2.5; // plastic between bolt head and ear head_d = 5.4; // M3 socket head pocket (slightly tight: press in warm, or glue) head_h = 3.2; $fn = 96; eps = 0.01; // ---------- derived ---------- cup_id = puck_d + fit; cup_od = cup_id + 2 * wall_t; cup_h = floor_t + puck_h + 0.2 + lip_t; hinge_z = cup_h / 2; // knuckle axis height in the cup frame k_off = hinge_r + 1.5; // cup outer wall -> hinge axis (ears clear the cup) hinge_y = -(cup_od / 2 + k_off); // knuckle axis position in the cup frame ear_in = knuckle_w / 2 + tooth_h + ear_spread; // inner face of an ear (as printed) axis_h = foot_t + hinge_r + 1; // hinge axis above the dashboard pitch = 360 / teeth; grip = 2 * ear_t + knuckle_w + 2 * tooth_h; // clamped stack when tight echo(str("Bolt: M3 x ", ceil(grip + knob_floor), " or a bit longer (M3x20 for defaults)")); echo(str("Detent step: ", pitch, " deg")); assert(cup_id - 2 * lip > glass_d, "lip would cover the glass"); // ---------- detent teeth ---------- // One radial tooth in the XY plane, along +x, pointing +z. module tooth(r0, r1, h) { a = pitch / 2 * 1.03; // neighbours overlap a little (shared edges are non-manifold) polyhedron( points = [[r0 * cos(-a), r0 * sin(-a), -eps], [r0 * cos(a), r0 * sin(a), -eps], [r0, 0, h], [r1 * cos(-a), r1 * sin(-a), -eps], [r1 * cos(a), r1 * sin(a), -eps], [r1, 0, h]], faces = [[0, 1, 2], [3, 5, 4], [0, 3, 4, 1], [1, 4, 5, 2], [0, 2, 5, 3]]); } // Tooth ring on the plane x = 0 around the x axis, pointing toward +x (dir = 1) or -x // (dir = -1). `phase` is the angle of tooth 0 in the YZ plane, measured from +y toward +z. module tooth_ring(dir, phase) { for (i = [0 : teeth - 1]) { al = phase + i * pitch; if (dir > 0) rotate([0, 90, 0]) rotate([0, 0, al + 90]) tooth(tooth_r_in, hinge_r - 0.3, tooth_h); else rotate([0, -90, 0]) rotate([0, 0, 90 - al]) tooth(tooth_r_in, hinge_r - 0.3, tooth_h); } } // ---------- cup ---------- module knuckle() { // in the cup frame translate([0, hinge_y, hinge_z]) { rotate([0, 90, 0]) cylinder(r = hinge_r, h = knuckle_w, center = true); // phase chosen so the teeth mesh with the ears when `tilt` is a multiple of `pitch` for (s = [-1, 1]) translate([s * knuckle_w / 2, 0, 0]) tooth_ring(s, pitch / 2 - 90); } // bridge from the disc to the cup wall translate([-knuckle_w / 2, hinge_y, 0]) cube([knuckle_w, -hinge_y - cup_id / 2 + 1, cup_h]); } module cup() { difference() { union() { cylinder(d = cup_od, h = cup_h); intersection() { knuckle(); translate([-50, -100, 0]) cube([100, 100, cup_h]); // keep it flat on the bed } } // puck pocket translate([0, 0, floor_t]) cylinder(d = cup_id, h = puck_h + 0.2); // lip opening with a lead-in chamfer translate([0, 0, floor_t + puck_h + 0.2 - eps]) cylinder(d1 = cup_id - 2 * lip, d2 = cup_id - 2 * lip + 2 * lip_t * 0.8, h = lip_t + 2 * eps); // push-out hole if (push_d > 0) translate([0, 0, -eps]) cylinder(d = push_d, h = floor_t + 2 * eps); // USB-C opening, full wall height above the floor rotate([0, 0, usb_angle]) translate([cup_id / 2 - 1, -usb_w / 2, floor_t]) cube([wall_t + 2, usb_w, cup_h]); // flex slots (skip the ones near the hinge and the USB opening) for (i = [0 : slots - 1]) { a = 360 / slots * (i + 0.5); if (adist(a, 270) > 30 && adist(a, usb_angle) > 25) rotate([0, 0, a]) translate([cup_id / 2 - 1, -slot_w / 2, floor_t + 2]) cube([wall_t + 2, slot_w, cup_h]); } // bolt hole translate([0, hinge_y, hinge_z]) rotate([0, 90, 0]) cylinder(d = bolt_d, h = 40, center = true, $fn = 32); } } function adist(a, b) = let(d = abs((a - b) % 360)) min(d, 360 - d); // ---------- base ---------- module rounded_plate(w, l, t, r) { hull() for (x = [-1, 1], y = [-1, 1]) translate([x * (w / 2 - r), y * (l / 2 - r), 0]) { cylinder(r = r, h = t - 1); cylinder(r = r - 1, h = t); // 1 mm top chamfer } } module ear() { // +x ear, inner face at x = ear_in translate([ear_in, 0, 0]) rotate([90, 0, 90]) linear_extrude(ear_t) hull() { translate([0, axis_h]) circle(r = hinge_r); translate([-hinge_r + 1, 0]) square([2 * hinge_r - 2, foot_t]); } translate([ear_in, 0, axis_h]) tooth_ring(-1, 0); } module base() { difference() { union() { rounded_plate(foot_w, foot_l, foot_t, foot_r); ear(); mirror([1, 0, 0]) ear(); } translate([0, 0, axis_h]) rotate([0, 90, 0]) cylinder(d = bolt_d, h = 60, center = true, $fn = 32); // captive nut, right ear, from the outside (vertex up: prints without support) translate([ear_in + ear_t - nut_h, 0, axis_h]) rotate([0, 90, 0]) cylinder(d = nut_af / cos(30), h = nut_h + 1, $fn = 6); } } // ---------- knob ---------- module knob() { h = knob_floor + head_h + 0.5; difference() { cylinder(d = knob_d, h = h); for (i = [0 : 7]) rotate([0, 0, i * 45]) translate([knob_d / 2 + 1.2, 0, -eps]) cylinder(r = 2.5, h = h + 2 * eps); // grip scallops translate([0, 0, -eps]) cylinder(d = bolt_d, h = h + 2 * eps, $fn = 32); translate([0, 0, knob_floor]) cylinder(d = head_d, h = h, $fn = 48); translate([0, 0, h - 0.6]) cylinder(d1 = knob_d - 6, d2 = knob_d - 4.8, h = 0.6 + eps); } } // ---------- dummy puck (preview only) ---------- module puck() { color("silver") cylinder(d = puck_d, h = puck_h); color("black") translate([0, 0, puck_h - 0.1]) cylinder(d = glass_d, h = 0.2); } // ---------- layout ---------- module cup_placed(t) { translate([0, 0, axis_h]) rotate([-t, 0, 0]) rotate([90, 0, 0]) translate([0, -hinge_y, -hinge_z]) children(); } if (part == "cup") cup(); else if (part == "base") base(); else if (part == "knob") knob(); else if (part == "print") { cup(); translate([cup_od / 2 + foot_w / 2 + 8, 0, 0]) base(); translate([cup_od / 2 + foot_w + knob_d / 2 + 14, 0, 0]) knob(); } else { t = round(tilt / pitch) * pitch; // snap preview to a detent color("dimgray") base(); cup_placed(t) { color("orange", 0.9) cup(); translate([0, 0, floor_t + 0.1]) puck(); } color("orange") translate([-ear_in - ear_t - (knob_floor + head_h + 0.5), 0, axis_h]) rotate([0, 90, 0]) knob(); }