13-Dash-Mount: dashboard holder (OpenSCAD + STLs), base printed
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
c22b98de76
commit
15b4ef5cef
7 files changed
+64018
-1
No files matched your search
@@ -0,0 +1,37 @@
|
||||
# 13-Dash-Mount
|
||||
|
||||
Dashboard holder for the JC3636W518 puck (used with `12-OBD-Speed`).
|
||||
Source: `dash_mount.scad` (OpenSCAD, all dimensions are parameters at the top). Ready STLs in `stl/`.
|
||||
|
||||
**Status (2026-10-24):** base printed and fits perfectly.
|
||||
|
||||
## Parts
|
||||
| Part | Print orientation | Notes |
|
||||
|---|---|---|
|
||||
| `cup.stl` | back on the bed | Snap-in cup: 0.9 mm lip over the bezel, flex slots, USB-C opening on the right (`usb_angle`), push-out hole in the back, hinge knuckle with detent teeth below the bottom edge |
|
||||
| `base.stl` | foot on the bed | Flat foot 40 × 46 mm for VHB tape, two hinge ears with teeth, captive M3 nut pocket in the right ear |
|
||||
| `knob.stl` | flat on the bed | Holds the M3 socket head (press it in warm, or glue it) |
|
||||
|
||||
No supports needed. ASA (dashboard heat), 0.2 mm layers, 4 perimeters (hinge strength), 30 % infill, brim/enclosure as usual for ASA.
|
||||
|
||||
## Hardware
|
||||
- M3 × 20 socket head bolt, M3 nut
|
||||
- 3M VHB / double-sided foam tape for the foot
|
||||
|
||||
## Assembly
|
||||
1. Press the bolt head into the knob (heat the head with a soldering iron, or add a drop of CA glue).
|
||||
2. Push the M3 nut into the hex pocket on the outside of the right ear.
|
||||
3. Put the cup's knuckle between the ears, then push the bolt through from the left and screw it into the nut.
|
||||
4. Snap the puck in with its USB-C port at the opening. The image orientation is set with the rotation setting in 12-OBD-Speed.
|
||||
|
||||
## Adjusting the angle
|
||||
Loosen the knob about one turn, which lets the ears spring apart so the teeth clear. Set the angle and tighten again.
|
||||
The teeth lock in **10° steps** (`teeth = 36`). The cup can tilt from about −30° (forward) to +80° (leaning back) without touching the base (checked in OpenSCAD).
|
||||
|
||||
## Tuning
|
||||
- **Measure your puck** with calipers and set `puck_d` / `puck_h`. `fit` (0.3 mm diametral) is the clearance.
|
||||
- Snap too tight or too loose: change `lip` (0.9) or `fit`.
|
||||
- Finer steps: raise `teeth` (e.g. 48 → 7.5°), but the teeth get small and print worse. 24 gives 15° steps and is the most robust option.
|
||||
- Teeth too hard to clear when loosened: increase `ear_spread`. If they don't lock firmly, decrease it.
|
||||
- Cable out on the left instead: `usb_angle = 180`.
|
||||
- `part = "assembly"` with `tilt` previews the mounted holder (snapped to a detent).
|
||||
@@ -0,0 +1,218 @@
|
||||
// Dashboard holder for the JC3636W518 round display (12-OBD-Speed)
|
||||
//
|
||||
// Three printed parts + M3x20 bolt + M3 nut + VHB tape:
|
||||
// cup - snap-in holder for the 58 x 11 mm puck, hinge knuckle at its bottom edge
|
||||
// base - flat foot (VHB tape) with two hinge ears, captive M3 nut in the right ear
|
||||
// knob - thumb knob that holds the M3 bolt head
|
||||
//
|
||||
// Angle adjustment: the knuckle and both ears carry radial face teeth (detents).
|
||||
// Loosen the knob ~1 turn -> the ears spring apart and the cup turns freely,
|
||||
// set the angle, tighten -> the teeth lock (360/teeth degrees per step).
|
||||
//
|
||||
// Print in ASA (dashboard heat). Orientation is already correct for every part:
|
||||
// cup : back on the bed (lip up) base : foot on the bed knob : flat on the bed
|
||||
//
|
||||
// Set `part` to "cup", "base" or "knob" and export each STL (F6, then F7).
|
||||
|
||||
part = "assembly"; // [assembly, cup, base, knob, print]
|
||||
tilt = 30; // assembly preview only: lean back from vertical (deg)
|
||||
|
||||
/* [Puck] */
|
||||
puck_d = 58.0; // metal case diameter
|
||||
puck_h = 11.0; // case thickness
|
||||
glass_d = 55.0; // cover glass diameter (lip must stay outside it)
|
||||
|
||||
/* [Cup] */
|
||||
fit = 0.3; // diametral clearance puck <-> cup
|
||||
wall_t = 2.0; // cup side wall
|
||||
floor_t = 2.0; // cup back
|
||||
lip = 0.9; // how far the snap lip reaches over the bezel (radial)
|
||||
lip_t = 1.2; // lip thickness
|
||||
push_d = 36; // hole in the back to push the puck out (0 = none)
|
||||
slots = 8; // flex slots in the wall (make the snap easier)
|
||||
slot_w = 1.2;
|
||||
usb_angle = 0; // USB-C opening: 0 = right, 180 = left (seen from the front)
|
||||
usb_w = 13; // opening width (USB-C plug overmold ~12 mm)
|
||||
|
||||
/* [Hinge] */
|
||||
teeth = 36; // detent teeth -> 360/teeth degrees per click
|
||||
tooth_h = 0.6; // tooth height
|
||||
tooth_r_in = 5.0; // inner radius of the tooth ring
|
||||
hinge_r = 9.0; // knuckle / ear disc radius (= outer radius of the teeth)
|
||||
knuckle_w = 8.0; // knuckle width (between the ears)
|
||||
ear_t = 4.0; // ear thickness
|
||||
ear_spread = 0.8; // extra gap per side as printed, so the teeth clear when loose
|
||||
bolt_d = 3.4; // M3 clearance hole
|
||||
nut_af = 5.7; // M3 nut across flats + clearance
|
||||
nut_h = 2.6; // nut pocket depth
|
||||
|
||||
/* [Base] */
|
||||
foot_w = 40; // across the car (x)
|
||||
foot_l = 46; // front-back (y)
|
||||
foot_t = 4;
|
||||
foot_r = 6; // corner radius
|
||||
|
||||
/* [Knob] */
|
||||
knob_d = 20;
|
||||
knob_floor = 2.5; // plastic between bolt head and ear
|
||||
head_d = 5.4; // M3 socket head pocket (slightly tight: press in warm, or glue)
|
||||
head_h = 3.2;
|
||||
|
||||
$fn = 96;
|
||||
eps = 0.01;
|
||||
|
||||
// ---------- derived ----------
|
||||
cup_id = puck_d + fit;
|
||||
cup_od = cup_id + 2 * wall_t;
|
||||
cup_h = floor_t + puck_h + 0.2 + lip_t;
|
||||
hinge_z = cup_h / 2; // knuckle axis height in the cup frame
|
||||
k_off = hinge_r + 1.5; // cup outer wall -> hinge axis (ears clear the cup)
|
||||
hinge_y = -(cup_od / 2 + k_off); // knuckle axis position in the cup frame
|
||||
ear_in = knuckle_w / 2 + tooth_h + ear_spread; // inner face of an ear (as printed)
|
||||
axis_h = foot_t + hinge_r + 1; // hinge axis above the dashboard
|
||||
pitch = 360 / teeth;
|
||||
|
||||
grip = 2 * ear_t + knuckle_w + 2 * tooth_h; // clamped stack when tight
|
||||
echo(str("Bolt: M3 x ", ceil(grip + knob_floor), " or a bit longer (M3x20 for defaults)"));
|
||||
echo(str("Detent step: ", pitch, " deg"));
|
||||
assert(cup_id - 2 * lip > glass_d, "lip would cover the glass");
|
||||
|
||||
// ---------- detent teeth ----------
|
||||
// One radial tooth in the XY plane, along +x, pointing +z.
|
||||
module tooth(r0, r1, h) {
|
||||
a = pitch / 2 * 1.03; // neighbours overlap a little (shared edges are non-manifold)
|
||||
polyhedron(
|
||||
points = [[r0 * cos(-a), r0 * sin(-a), -eps], [r0 * cos(a), r0 * sin(a), -eps], [r0, 0, h],
|
||||
[r1 * cos(-a), r1 * sin(-a), -eps], [r1 * cos(a), r1 * sin(a), -eps], [r1, 0, h]],
|
||||
faces = [[0, 1, 2], [3, 5, 4], [0, 3, 4, 1], [1, 4, 5, 2], [0, 2, 5, 3]]);
|
||||
}
|
||||
|
||||
// Tooth ring on the plane x = 0 around the x axis, pointing toward +x (dir = 1) or -x
|
||||
// (dir = -1). `phase` is the angle of tooth 0 in the YZ plane, measured from +y toward +z.
|
||||
module tooth_ring(dir, phase) {
|
||||
for (i = [0 : teeth - 1]) {
|
||||
al = phase + i * pitch;
|
||||
if (dir > 0) rotate([0, 90, 0]) rotate([0, 0, al + 90]) tooth(tooth_r_in, hinge_r - 0.3, tooth_h);
|
||||
else rotate([0, -90, 0]) rotate([0, 0, 90 - al]) tooth(tooth_r_in, hinge_r - 0.3, tooth_h);
|
||||
}
|
||||
}
|
||||
|
||||
// ---------- cup ----------
|
||||
module knuckle() { // in the cup frame
|
||||
translate([0, hinge_y, hinge_z]) {
|
||||
rotate([0, 90, 0]) cylinder(r = hinge_r, h = knuckle_w, center = true);
|
||||
// phase chosen so the teeth mesh with the ears when `tilt` is a multiple of `pitch`
|
||||
for (s = [-1, 1]) translate([s * knuckle_w / 2, 0, 0]) tooth_ring(s, pitch / 2 - 90);
|
||||
}
|
||||
// bridge from the disc to the cup wall
|
||||
translate([-knuckle_w / 2, hinge_y, 0]) cube([knuckle_w, -hinge_y - cup_id / 2 + 1, cup_h]);
|
||||
}
|
||||
|
||||
module cup() {
|
||||
difference() {
|
||||
union() {
|
||||
cylinder(d = cup_od, h = cup_h);
|
||||
intersection() {
|
||||
knuckle();
|
||||
translate([-50, -100, 0]) cube([100, 100, cup_h]); // keep it flat on the bed
|
||||
}
|
||||
}
|
||||
// puck pocket
|
||||
translate([0, 0, floor_t]) cylinder(d = cup_id, h = puck_h + 0.2);
|
||||
// lip opening with a lead-in chamfer
|
||||
translate([0, 0, floor_t + puck_h + 0.2 - eps])
|
||||
cylinder(d1 = cup_id - 2 * lip, d2 = cup_id - 2 * lip + 2 * lip_t * 0.8, h = lip_t + 2 * eps);
|
||||
// push-out hole
|
||||
if (push_d > 0) translate([0, 0, -eps]) cylinder(d = push_d, h = floor_t + 2 * eps);
|
||||
// USB-C opening, full wall height above the floor
|
||||
rotate([0, 0, usb_angle]) translate([cup_id / 2 - 1, -usb_w / 2, floor_t])
|
||||
cube([wall_t + 2, usb_w, cup_h]);
|
||||
// flex slots (skip the ones near the hinge and the USB opening)
|
||||
for (i = [0 : slots - 1]) {
|
||||
a = 360 / slots * (i + 0.5);
|
||||
if (adist(a, 270) > 30 && adist(a, usb_angle) > 25)
|
||||
rotate([0, 0, a]) translate([cup_id / 2 - 1, -slot_w / 2, floor_t + 2])
|
||||
cube([wall_t + 2, slot_w, cup_h]);
|
||||
}
|
||||
// bolt hole
|
||||
translate([0, hinge_y, hinge_z]) rotate([0, 90, 0]) cylinder(d = bolt_d, h = 40, center = true, $fn = 32);
|
||||
}
|
||||
}
|
||||
|
||||
function adist(a, b) = let(d = abs((a - b) % 360)) min(d, 360 - d);
|
||||
|
||||
// ---------- base ----------
|
||||
module rounded_plate(w, l, t, r) {
|
||||
hull() for (x = [-1, 1], y = [-1, 1])
|
||||
translate([x * (w / 2 - r), y * (l / 2 - r), 0]) {
|
||||
cylinder(r = r, h = t - 1);
|
||||
cylinder(r = r - 1, h = t); // 1 mm top chamfer
|
||||
}
|
||||
}
|
||||
|
||||
module ear() { // +x ear, inner face at x = ear_in
|
||||
translate([ear_in, 0, 0]) rotate([90, 0, 90]) linear_extrude(ear_t)
|
||||
hull() {
|
||||
translate([0, axis_h]) circle(r = hinge_r);
|
||||
translate([-hinge_r + 1, 0]) square([2 * hinge_r - 2, foot_t]);
|
||||
}
|
||||
translate([ear_in, 0, axis_h]) tooth_ring(-1, 0);
|
||||
}
|
||||
|
||||
module base() {
|
||||
difference() {
|
||||
union() {
|
||||
rounded_plate(foot_w, foot_l, foot_t, foot_r);
|
||||
ear();
|
||||
mirror([1, 0, 0]) ear();
|
||||
}
|
||||
translate([0, 0, axis_h]) rotate([0, 90, 0]) cylinder(d = bolt_d, h = 60, center = true, $fn = 32);
|
||||
// captive nut, right ear, from the outside (vertex up: prints without support)
|
||||
translate([ear_in + ear_t - nut_h, 0, axis_h]) rotate([0, 90, 0])
|
||||
cylinder(d = nut_af / cos(30), h = nut_h + 1, $fn = 6);
|
||||
}
|
||||
}
|
||||
|
||||
// ---------- knob ----------
|
||||
module knob() {
|
||||
h = knob_floor + head_h + 0.5;
|
||||
difference() {
|
||||
cylinder(d = knob_d, h = h);
|
||||
for (i = [0 : 7]) rotate([0, 0, i * 45]) translate([knob_d / 2 + 1.2, 0, -eps])
|
||||
cylinder(r = 2.5, h = h + 2 * eps); // grip scallops
|
||||
translate([0, 0, -eps]) cylinder(d = bolt_d, h = h + 2 * eps, $fn = 32);
|
||||
translate([0, 0, knob_floor]) cylinder(d = head_d, h = h, $fn = 48);
|
||||
translate([0, 0, h - 0.6]) cylinder(d1 = knob_d - 6, d2 = knob_d - 4.8, h = 0.6 + eps);
|
||||
}
|
||||
}
|
||||
|
||||
// ---------- dummy puck (preview only) ----------
|
||||
module puck() {
|
||||
color("silver") cylinder(d = puck_d, h = puck_h);
|
||||
color("black") translate([0, 0, puck_h - 0.1]) cylinder(d = glass_d, h = 0.2);
|
||||
}
|
||||
|
||||
// ---------- layout ----------
|
||||
module cup_placed(t) {
|
||||
translate([0, 0, axis_h]) rotate([-t, 0, 0]) rotate([90, 0, 0])
|
||||
translate([0, -hinge_y, -hinge_z]) children();
|
||||
}
|
||||
|
||||
if (part == "cup") cup();
|
||||
else if (part == "base") base();
|
||||
else if (part == "knob") knob();
|
||||
else if (part == "print") {
|
||||
cup();
|
||||
translate([cup_od / 2 + foot_w / 2 + 8, 0, 0]) base();
|
||||
translate([cup_od / 2 + foot_w + knob_d / 2 + 14, 0, 0]) knob();
|
||||
}
|
||||
else {
|
||||
t = round(tilt / pitch) * pitch; // snap preview to a detent
|
||||
color("dimgray") base();
|
||||
cup_placed(t) {
|
||||
color("orange", 0.9) cup();
|
||||
translate([0, 0, floor_t + 0.1]) puck();
|
||||
}
|
||||
color("orange") translate([-ear_in - ear_t - (knob_floor + head_h + 0.5), 0, axis_h])
|
||||
rotate([0, 90, 0]) knob();
|
||||
}
|
||||
File diff suppressed because it is too large.
Load diff
Binary file not shown.
File diff suppressed because it is too large.
Load diff
File diff suppressed because it is too large.
Load diff
@@ -81,7 +81,7 @@ Display color format is `RGB565_SWAPPED` (ST77916 byte order, set in `lv_conf.h`
|
||||
| `tools` | `gif_to_360.py` — converts GIFs to 360×360 for the device (Pillow; scale to cover + center crop, keeps frame timing) |
|
||||
| `shared` | **Shared code for all JC3636W518 projects:** `jc3636w518.ini` (PlatformIO base config), `include/lv_conf.h` (LVGL 9.6), `lib/JC3636W518` (board library). See its `README.md` |
|
||||
| `12-OBD-Speed` | **The new program — working in the car (2026-10-23):** speed from the ELM327 over BLE as big number + arc gauge on a GIF background, battery-voltage arc in the bottom gap, idle/screen-off mode (both **verified by the user**); swipe left for the adapter menu (scan, select → remembered in NVS, auto-reconnect every 3 s), again for settings (rotation, idle/screen-off timeout), again for the background (GIF from SD `/gifs` copied into an 11.9 MB raw flash partition, own `partitions.csv`). See its `README.md` |
|
||||
| `13-Dash-Mount` | **3D-printed dashboard holder** (OpenSCAD, 2026-10-23, not yet printed): snap-in cup with lip over the bezel + USB-C opening on the side, detent tilt hinge (36 face teeth = 10° steps, M3×20 bolt + captive nut + printed knob), flat foot for VHB tape. ASA. User's choices: adhesive base, detent hinge, M3, cable exits sideways, only a USB-C opening needed. OpenSCAD is installed (`C:\Program Files\OpenSCAD\openscad.exe`, use from bash for `-D part="..."` quoting). See its `README.md` |
|
||||
| `13-Dash-Mount` | **3D-printed dashboard holder** (OpenSCAD, 2026-10-23; **base printed 2026-10-24, user: "perfect"**): snap-in cup with lip over the bezel + USB-C opening on the side, detent tilt hinge (36 face teeth = 10° steps, M3×20 bolt + captive nut + printed knob), flat foot for VHB tape. ASA. User's choices: adhesive base, detent hinge, M3, cable exits sideways, only a USB-C opening needed. OpenSCAD is installed (`C:\Program Files\OpenSCAD\openscad.exe`, use from bash for `-D part="..."` quoting). See its `README.md` |
|
||||
| `10-GIF-Tests` | **GIF playback experiments** (was `10-OBD-Display-2024`): `display_gif_embedded`, `display_gif_sd`, `assets/gifs`. The 2024 bridge/ELMulator/WiFi speed sketch, the broken LVGL 9 archive and the BLE scanner tool (`11-BLE-Scanner`: on-screen scan, GATT listing, ELM test, LittleFS log) were removed 2026-10-23 — all in git history |
|
||||
| `3-Specification` | Spec sheet (factory firmware features, interface photo) |
|
||||
| `4-Chip manual` | ESP32-S3R8 datasheet, PCM5100A datasheet |
|
||||
|
||||
Reference in new issue
Block a user