37 lines
2.2 KiB
Markdown
37 lines
2.2 KiB
Markdown
# 13-Dash-Mount
|
||||
|
|
|
|||
|
|
Dashboard holder for the JC3636W518 puck (used with `12-OBD-Speed`).
|
|||
|
|
Source: `dash_mount.scad` (OpenSCAD, all dimensions are parameters at the top). Ready STLs in `stl/`.
|
|||
|
|
|
|||
|
|
**Status (2026-10-24):** base printed and fits perfectly.
|
|||
|
|
|
|||
|
|
## Parts
|
|||
|
|
| Part | Print orientation | Notes |
|
|||
|
|
|---|---|---|
|
|||
|
|
| `cup.stl` | back on the bed | Snap-in cup: 0.9 mm lip over the bezel, flex slots, USB-C opening on the right (`usb_angle`), push-out hole in the back, hinge knuckle with detent teeth below the bottom edge |
|
|||
|
|
| `base.stl` | foot on the bed | Flat foot 40 × 46 mm for VHB tape, two hinge ears with teeth, captive M3 nut pocket in the right ear |
|
|||
|
|
| `knob.stl` | flat on the bed | Holds the M3 socket head (press it in warm, or glue it) |
|
|||
|
|
|
|||
|
|
No supports needed. ASA (dashboard heat), 0.2 mm layers, 4 perimeters (hinge strength), 30 % infill, brim/enclosure as usual for ASA.
|
|||
|
|
|
|||
|
|
## Hardware
|
|||
|
|
- M3 × 20 socket head bolt, M3 nut
|
|||
|
|
- 3M VHB / double-sided foam tape for the foot
|
|||
|
|
|
|||
|
|
## Assembly
|
|||
|
|
1. Press the bolt head into the knob (heat the head with a soldering iron, or add a drop of CA glue).
|
|||
|
|
2. Push the M3 nut into the hex pocket on the outside of the right ear.
|
|||
|
|
3. Put the cup's knuckle between the ears, then push the bolt through from the left and screw it into the nut.
|
|||
|
|
4. Snap the puck in with its USB-C port at the opening. The image orientation is set with the rotation setting in 12-OBD-Speed.
|
|||
|
|
|
|||
|
|
## Adjusting the angle
|
|||
|
|
Loosen the knob about one turn, which lets the ears spring apart so the teeth clear. Set the angle and tighten again.
|
|||
|
|
The teeth lock in **10° steps** (`teeth = 36`). The cup can tilt from about −30° (forward) to +80° (leaning back) without touching the base (checked in OpenSCAD).
|
|||
|
|
|
|||
|
|
## Tuning
|
|||
|
|
- **Measure your puck** with calipers and set `puck_d` / `puck_h`. `fit` (0.3 mm diametral) is the clearance.
|
|||
|
|
- Snap too tight or too loose: change `lip` (0.9) or `fit`.
|
|||
|
|
- Finer steps: raise `teeth` (e.g. 48 → 7.5°), but the teeth get small and print worse. 24 gives 15° steps and is the most robust option.
|
|||
|
|
- Teeth too hard to clear when loosened: increase `ear_spread`. If they don't lock firmly, decrease it.
|
|||
|
|
- Cable out on the left instead: `usb_angle = 180`.
|
|||
|
|
- `part = "assembly"` with `tilt` previews the mounted holder (snapped to a detent).
|