- README / CLAUDE.md layout: dongle/, hardware/, tools/ submodule, make_remote_hmi.py; telemetry in the protocol; the PC can take the robot's place on the radio. CLAUDE.md: NextionUI is on Serial2 (said Serial1); remote-without-robot via the dongle + sim. - remote/README: MPU6050 supply row; stick calibration button names of the new SETUP page; upload/USB-port hints. - remote/NEXTION.md: display on Serial2, how the Editor upload goes. - robot/README: Battery in the file list, Comms/ServoDriver roles, packet structs instead of payload size, check the IMU gives live data (the remote's MPU6050 needed a full reset; RobotIMU::begin() only wakes it). - sim/README: smoke test covers telemetry and servo calibration; OpenScadModel. - dongle/README: AT2401C test result, app command table, SignalRGB note, air settings incl. ack payloads. - PLANNING.md: the display direction is in the generated HMI. - Unity README: what the project is. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
9.6 KiB
Hexapod remote firmware (Teensy 4.0)
Handheld transmitter for the hexapod. It reads two 3-axis twist-grip
joysticks and an MPU6050, takes operator commands from a Nextion
touchscreen, and sends a CmdPacket (defined in
../shared/HexapodProtocol/HexapodProtocol.h) to the robot over nRF24L01
at 100 Hz. The robot's Telemetry comes back in the radio's ack payloads.
Without the robot, the Unity simulation can answer instead, through the
USB nRF24 dongle (../sim/README.md).
Planned
- Battery level (divider not built yet): read the 18650's voltage through a
~100k/100k divider from the cell's + (not the boost board's 5 V output)
into A6 (pin 20, free), with 100 nF to GND. Details in
../hardware/openscad/PLANNING.md(notes for future designs). The firmware side is done (Battery, shown on the STATUS page): setBATTERY_SENSE_PIN = A6inConfig.honce it's wired. A low-battery warning is still to do.
Building
From the 2026-current folder: pio run -e remote, flash with
pio run -e remote -t upload, monitor with pio device monitor -e remote.
The upload opens Teensy Loader; if the Teensy doesn't reboot into it by
itself, press its program button. If flashing works but the USB serial port
then won't open or goes quiet, try another USB port or cable before
suspecting the firmware (a bare Teensy 4.0 showed exactly that on one port).
Wiring (edge headers only; edit Config.h if yours differs)
| Part | Signal | Teensy 4.0 pin |
|---|---|---|
| nRF24L01 | MOSI / MISO / SCK | 11 / 12 / 13 (SPI0) |
| nRF24L01 | CE / CSN | 9 / 10 |
| nRF24L01 | VCC | 3.3 V, with a 10–100 µF cap right at the module |
| MPU6050 | SDA / SCL | 18 / 19 (Wire) |
| MPU6050 | VCC | 3.3 V (a GY-521 runs fine on it). Check the polarity: one supply reversal killed the first board's regulator |
| Nextion | TX → RX2, RX ← TX2 | 7 / 8 (Serial2), 5 V supply (found on the real remote) |
| Sticks | 6 axes | left stick X / Y / twist on A3 / A7 / A8 (17 / 21 / 22), right stick on A0 / A1 / A2 (14 / 15 / 16). A7/A8 hold the two wires that were on A4/A5 (18/19). All but the right twist read inverted (STICK_INVERT). Checked on the real remote |
| Battery (planned) | divider | A6 (20) |
Rewiring from the old remote: move the two stick wires from 18/19 to
21/22, then put the MPU on 18/19 (Wire). The old remote had its MPU code
switched off, probably because A4/A5 double as Wire's pins. Redo the stick
axis check (p dump) and the sweep calibration afterwards.
Stick pots are wired 3.3 V – wiper – GND. Never feed 5 V into a Teensy 4.x analog pin.
Control scheme
| Input | Packet field | Meaning on the robot |
|---|---|---|
| Left stick forward/back | vx |
walk forward/back |
| Left stick left/right | vy |
strafe (mode A); heading target direction (mode B) |
| Left stick twist | yaw_rate |
turn rate (mode A only; ignored in mode B) |
| Right stick, ROTATE (default) | rx/ry/rz |
body roll / pitch / yaw |
Right stick, MOVE (FLAG_RSTICK_XLATE) |
rx/ry/rz |
body X / Y / Z (height, via twist) offset |
| Handset tilt | remote_roll/pitch |
extra body roll/pitch while REMOTE GYRO is on |
| Height slider | body_height |
standing height, default ± STANCE_HEIGHT_RANGE_MM (robot rate-limits the change) |
In HEADING mode the left stick steers, relative to where the robot faces at that moment. Forward/back walks forward/back, and sideways steers: forward+left or back+left walk while turning left, and left alone turns on the spot for as long as you hold it. Let go and the robot holds its heading.
Touchscreen (NEXTION.md has the details), with tabs along the bottom and
a red DISARM on every page:
- DRIVE: ARM / DISARM, SIT/STAND, TRIPOD/WAVE, DIRECT/HEADING, R: ROTATE/MOVE, REMOTE GYRO, ROBOT GYRO, speed and height sliders.
- STATUS: handset and robot IMU roll/pitch, the six stick axes, both batteries, radio quality and the robot's received packet rate.
- SERVOS: all 18 joint angles the robot is commanding, as a top view.
- CAL: servo centre calibration (see below).
- SETUP: stick calibration (CAL STICKS / CANCEL), LEVEL REMOTE (re-zero the handset tilt), UPDATE DISPLAY, backlight.
Everything about the robot comes from its telemetry, which rides back on
the radio's ack payloads (Telemetry in HexapodProtocol.h): RadioLink
reads it after every send, and it counts as stale after
TELEMETRY_STALE_MS.
Servo centre calibration (CAL page)
- Put the robot on a stand, legs free, and disarm.
- Tap START. The robot drives every servo to its centre pose: coxa 0, femur 0, tibia −90 (legs straight out, shins straight down).
- Pick a leg (FR MR RR RL ML FL) and a joint. The remote first reads that
servo's trim back from the robot (the trim box shows
...until then). - Step the trim with −10 / −1 / +1 / +10 µs (or ZERO) until the horn is exactly square. SAVE TO ROBOT turns orange while there are unsaved trims.
- SAVE TO ROBOT stores all 18 trims in the robot's EEPROM. REVERT drops unsaved changes. STOP, leaving the page, or a link loss relaxes the servos. Arming is refused while calibrating.
Safety interlocks (in RemoteState)
- Arming is refused unless every stick axis is centered, and never allowed during stick or servo calibration. Servo calibration only starts while disarmed, and stops when you leave the CAL page or the link drops.
- UPDATE DISPLAY needs a second tap within 3 s and is refused while armed.
- Disarming always clears the stand request. The robot arms into SIT, so re-arming never stands it up by itself.
- Link loss: if no ack arrives for
LINK_LOST_MS(300 ms, matching the robot's failsafe), the remote disarms itself. When the link comes back the robot stays down until you re-arm deliberately. - Sit/stand requests are only accepted while armed.
FLAG_WALKis only sent while standing is requested. - While disarmed or calibrating, all motion fields are sent as zero.
Smoothing
- Speed scale ramps toward the slider at
SPEED_SCALE_RATE_PER_SEC. The robot uses speed scale directly on the walking twist, so a slider jump would otherwise be a velocity step. - Remote tilt fades in/out over ~0.5 s when REMOTE GYRO is toggled, and the handset re-zeroes its "level" at the moment you enable it.
- FLAG_WALK lingers 250 ms after the left stick centers, so hovering at the deadzone edge doesn't make the robot chatter between STAND and WALKING.
- Body pose smoothing is left to the robot's
BodyPoserate limiters.
Stick calibration
- Power on with both sticks released and the remote held still. Each axis's resting center is captured automatically.
- For full calibration, disarm, then tap CAL STICKS on the SETUP page
(or press
con the serial console). Move every axis of both sticks to both limits, release them, and tap SAVE CAL (c). The result is saved to EEPROM, so it survives power cycles and reflashing. - If any axis moved less than
CAL_MIN_HALF_SPANeither side of center, the save is refused and you stay in calibration mode. CANCEL (x) aborts. pprints the calibration in a form you can paste intoConfig.hdefaults.Rwipes EEPROM back to theConfig.hdefaults.
Serial console (USB, 115200, single keystrokes)
Every touchscreen control is available here, so you can bench-test with no display attached.
| Key | Action | Key | Action |
|---|---|---|---|
a |
toggle arm | k |
disarm |
s |
toggle sit/stand | g |
tripod ↔ wave |
m |
direct ↔ heading-hold | t |
right stick rotate ↔ translate |
r |
remote gyro on/off | b |
robot gyro on/off |
+ / - |
speed ±25 | z |
zero handset level |
] / [ |
height up / down 10% | ||
c |
start / save calibration | x |
cancel calibration |
p |
print status (raw + mapped sticks, IMU, link, state, cal) | d |
toggle 10 Hz packet dump |
R |
reset stick cal to Config defaults | U |
Nextion upload mode (USB ↔ display; power-cycle to leave) |
o |
servo calibration start/stop | n |
next servo (leg × 3 + joint) |
, / . |
trim −1 / +1 µs | < / > |
trim −10 / +10 µs |
0 |
trim to zero | w / e |
save trims on the robot / revert |
p also prints the robot's telemetry (state, IMU, battery, joint angles)
and the servo-calibration state.
Bench-check checklist
- Stick directions: with
p, confirm each logical axis reads positive for right / forward / counterclockwise twist. Flip it inSTICK_INVERT[]if not. Done on the real remote (2026-11-17), then the sweep calibration. - IMU mounting: with
p, dip the right edge down to get +roll, and tip the far edge down to get +pitch. If not, fixIMU_AXIS_FROM_CHIP/IMU_AXIS_SIGN. Done (defaults are right). The first GY-521 got its supply reversed once and its regulator now runs hot: redo this check on the replacement, and see whether it still needs the reset inRemoteIMU::begin(). - Nextion: the generated HMI sets
bauds=115200in Program.s and is on the display (upload through SETUP › UPDATE DISPLAY or serialU). - Radio: with the robot (or the Unity sim behind the USB dongle)
running,
tLink/pshould show ~100%, andpshould print robot telemetry. If it reads NO LINK, check that both ends were built from the sameHexapodProtocol.h: each end drops packets of the wrong size. Done against the Unity sim through the dongle; not yet with the robot. - End to end with the robot on a stand: use
dto dump packets and confirm each field changes the way the table above says.