// Remote v2: a flat console for the same electronics as the original remote // (remote.scad, kept as the record of the printed one). Draft 3, not printed. // // Use (owner): both hands wrap the big twist-grip sticks, so nothing holds // the case. It hangs from a neck strap on one eyelet on the top face, near // the balance point and behind the display (slide it in its slots to balance), // with a fold-out bail that braces against the body; or it lies on a table on // its kickstand. The sticks sit far apart and nothing rises above the top face // near them. // // Two shells split horizontally, printed in ASA: the top shell face down, // the bottom shell on its flat underside, both without supports. The // kickstand, strap eyelet and brace bail are separate parts. The shells are joined by M3 screws from below // into heat-set inserts in the top shell. // // Frame: u to the right, v away from the user (the far edge is the front), // Z up, Z = 0 on the top face. // // Electronics (all reused): 2 x JH-D300X-R1 joystick, Nextion NX4832T035 // (3.5"), 18650 UPS/boost board (89 x 22), Teensy 4.0, GY-521 (MPU6050), // 12 x 15 mm 4-pin USB-C breakout (V, D-, D+, G), slide switch (the robot's). // Wiring (owner): the breakout's V/G go to the UPS board's charge input and // D-/D+ to the Teensy, through two halves of a cut USB cable whose plugs go // into the UPS board and the Teensy; the UPS output feeds the Teensy. /* [Shell] */ T = 2.4; // walls and floor (6 perimeters of 0.4) PLATE = 3.0; // top plate Z_BOT = -32; // flat underside (32 mm thick: the D300X sticks reach 28.5 down) Z_SPLIT = -12; // top shell / bottom shell CHAMFER = 4; // 45 deg bottom edge (printable without support) TOP_CHAMFER = 1.5; // 45 deg top edge (the top shell prints face down) LIP_H = 2.5; // locating lip on the bottom shell, into the top shell LIP_W = 1.2; FIT = 0.2; // clearance per side between printed parts /* [Outline] */ STICKS = [[-80, 0], [80, 0]]; STICK_SQ = [28, 40]; // half size (u, v) of the rounded box around each stick STICK_SQ_R = 10; FRONT_BAND = [[-60, 0], [60, 52]]; // u, v box: display, USB-C, Teensy FRONT_V = FRONT_BAND[1][1]; SIDE_U = STICKS[1][0] + STICK_SQ[0]; // the flat side faces REAR_BAND = [[-80, -64], [80, 0]]; // UPS board behind the strap eyelet, switch behind that CORNER_R = 10; /* [Fasteners] */ // M3 x 12 from below; heat-set insert M3 (4.0 mm hole, 5.7 mm long) in the top shell SCREWS = [[-58, 32], [58, 32], [-70, -52], [70, -52]]; BOSS_D = 9; INSERT_D = 4.0; INSERT_L = 6; SCREW_D = 3.4; HEAD_D = 6.5; HEAD_Z = -19; // counterbore floor: 7 mm of tower + 5 mm into the insert /* [Joysticks] */ STICK_HOLE_D = 40; STICK_SCREW = 16.25; // 4 x M2.5 x 14 on a 32.5 mm square, through cover and plate into the control box STICK_SCREW_D = 2.8; /* [Display: Nextion NX4832T035] */ NX_BOARD = [100.5, 54.94]; NX_HOLES = [94.2, 48.5]; // M3 grid, centred on the board NX_CENTRE = [0, 20]; // board centre (forward of the sticks, so the strap misses it) NX_FLIP = true; // display mounted turned 180 deg (its J1 connector on the right, clear of // the Teensy's USB plug): set display direction 180 in the Nextion Editor NX_WIN_OFF = [NX_FLIP ? 2.15 : -2.15, 0]; // window (visible area) centre from the board centre NX_WINDOW = [75.9, 50.9]; // opening in the plate NX_LCD = [84, 54]; // LCD module outline NX_LCD_T = 4.5; // LCD thickness: approximate, measure before printing NX_BEZEL = 1.5; // plate left above the glass NX_POST_D = 5.5; // clears the LCD module by 0.2 mm NX_SCREW_D = 2.2; // M2.5 self-tapping through the board /* [Switch: slide switch, mounted on top] */ SWITCH_POS = [0, -56]; SWITCH_SLOT = [16, 8]; // 8 x 16 slot and d2 holes 19 apart: fit the switch exactly (owner, old remote) SWITCH_PITCH = 19; SWITCH_HOLE_D = 2.0; ENGRAVE_D = 0.6; // ON/OFF inlay: the first 3 layers (0.2) of the face-down top shell /* [USB-C breakout] */ USBC_BOARD = [12, 15, 1.6]; USBC_RCPT = [8.94, 7.35, 3.26]; // receptacle, flush with the board's front edge USBC_POS = [-45, 0]; // board centre u (v follows from the front wall) USBC_Z = Z_BOT + 10; // board underside /* [Other boards] */ UPS_CENTRE = [0, -41]; UPS_LEDS = [[-23.9, 0], [23.9, 0]]; // charge / on LEDs, seen through 2 x 6 mm floor slots (as on the old remote) UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote) UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate /* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */ // Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the // owner's photos: measure before printing. Board frame: x across (0..52), y // along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80. PERF = [52, 80, 1.6]; // Held by 4 clamps on its long sides, no holes in the board (owner): a post // beside the edge carries the board's edge on its inner half, and an M3 x 8 // button head with a washer (d7) in a heat-set insert in the post clamps it. PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm) PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board) PERF_IMU = [23, 38]; // GY-521 on the main board (owner), on 8.5 mm headers: its corner, board frame /* [Kickstand] */ KS_W = 30; // flap width (u) KS_V = [8, 43.75]; // free end, hinge axis (the trough clears the main board) KS_T = 3; KS_BARREL_D = 6.5; KS_PIN_D = 3.3; // M3 x 40 screw, from inside on the left, into a nut trap on the right KS_WALL = 3; // side walls (nut trap) KS_WALL_V = 2; // front/back walls /* [Strap eyelet] */ // A loop on the top face for the neck strap's snap hook, near the balance // point (estimated centre of mass v -3, Z -18: with the eyelet at v -24 the // remote hangs level when the strap leaves at ~34 deg from vertical). // Two M3 x 8 button heads into heat-set inserts; the slots give // +-HOOK_TRAVEL to balance it. HOOK_POS = [0, -24]; HOOK_TRAVEL = 5; HOOK_INSERTS = 7; // +- u HOOK_BASE = [24, 18, 4]; // u, v, Z // Alternative place: the front face (the edge away from you), 2 inserts in // the front wall of the bottom shell; the loop then points forward. HOOK_FRONT_Z = -19; HOOK_MOUNT = "top"; // [top, front] (assembly view only) HOOK_HOLE_D = 8; // for the snap hook HOOK_H = 16; // top of the loop above the top face /* [Brace bail] */ // A U-shaped bail pivoting on the side faces, outside the case and below the // hands. Folded forward it wraps the front edge; swung back and down its // crossbar rests against your chest or belly. M3 x 16 button-head screws // with a washer into heat-set inserts in the side walls; friction holds it. BAIL_PIVOT = [-25, -22]; // v, Z on the side faces (u +-SIDE_U) BAIL_L = 82; // pivot to crossbar centre line BAIL_BOW = 10; // crossbar bows outwards by this much in the middle BAIL_T = 5; // arm thickness (u) BAIL_H = 12; // arm and crossbar height BAIL_GAP = 0.5; // arm to side face (a washer fills it) BAIL_ANGLE = 0; // 0 = folded forward, swings down: -90 hanging, -180 straight back, ~-150 brace /* [Rendering] */ PART = "assembly"; // [assembly, top, inlay, text, bottom, kickstand, eyelet, bail] SHOW_TOP = true; SHOW_BOTTOM = true; SHOW_PARTS = true; SHOW_STICKS = true; KS_OPEN = 0; // kickstand angle, deg EXPLODE = 0; /* [Hidden] */ $fa = 4; $fs = 0.5; BIG = 400; JOIN = 1; module lx(h) linear_extrude(h, convexity = 10) children(); module rbox(b, r) translate(b[0] + [r, r]) offset(r = r) square(b[1] - b[0] - [2 * r, 2 * r]); module rsq(c, h, r) translate(c) offset(r = r) square(2 * (h - [r, r]), center = true); // ---------- outline and solid ---------------------------------------------- module outline_2d() hull() { rbox(FRONT_BAND, CORNER_R); rbox(REAR_BAND, CORNER_R); for (s = STICKS) rsq(s, STICK_SQ, STICK_SQ_R); } // The outline swept with a 45 deg chamfer at the bottom (and optionally at // the top): a thin slab of the outline, inset by the chamfer, Minkowski'd // with a turned profile. `inset` gives the inner surface of the walls. module swept(inset, z0, z1, top_chamfer) { c = CHAMFER; h = z1 - z0; tc = top_chamfer; minkowski() { translate([0, 0, z0]) linear_extrude(0.01) offset(delta = -(c + inset)) outline_2d(); rotate_extrude($fn = 32) polygon([[0, 0], [c, c], [c, h - tc], [c - tc, h], [0, h]]); } } module outer_solid() swept(0, Z_BOT, 0, TOP_CHAMFER); module inner_solid() swept(T, Z_BOT + T, BIG / 4, 0); // ---------- top shell ------------------------------------------------------- module nx_holes() for (du = [-1, 1], dv = [-1, 1]) translate(NX_CENTRE + [du * NX_HOLES[0], dv * NX_HOLES[1]] / 2) children(); module stick_screws() for (s = STICKS, du = [-1, 1], dv = [-1, 1]) translate(s + [du, dv] * STICK_SCREW) children(); NX_WIN = NX_CENTRE + NX_WIN_OFF; NX_BOARD_TOP = -NX_BEZEL - NX_LCD_T; // board's top face module top_shell() render(convexity = 10) difference() { union() { intersection() { outer_solid(); difference() { translate([-BIG / 2, -BIG / 2, Z_SPLIT]) cube([BIG, BIG, -Z_SPLIT]); difference() { inner_solid(); translate([-BIG / 2, -BIG / 2, -PLATE]) cube(BIG); } } } // eyelet inserts for (m = [-1, 1]) translate([HOOK_POS[0] + m * HOOK_INSERTS, HOOK_POS[1], -PLATE - 7 + JOIN]) cylinder(d = 8, h = 7); // screw bosses for (s = SCREWS) translate([s[0], s[1], Z_SPLIT]) cylinder(d = BOSS_D, h = -Z_SPLIT - PLATE + JOIN); // display posts nx_holes() translate([0, 0, NX_BOARD_TOP]) cylinder(d = NX_POST_D, h = -NX_BOARD_TOP - PLATE + JOIN); // joystick nut bosses } // display: window (chamfered to the top) and LCD pocket translate(concat(NX_WIN, -NX_BEZEL - 0.01)) hull() { translate([0, 0, 0.005]) cube(concat(NX_WINDOW, 0.01), center = true); translate([0, 0, NX_BEZEL + 0.01]) cube(concat(NX_WINDOW + [2, 2] * NX_BEZEL, 0.02), center = true); } translate(concat(NX_WIN - (NX_LCD + [1, 1]) / 2, -PLATE - 1)) cube(concat(NX_LCD + [1, 1], PLATE + 1 - NX_BEZEL)); nx_holes() translate([0, 0, NX_BOARD_TOP - 1]) cylinder(d = NX_SCREW_D, h = 1 + 4.5); // joysticks for (s = STICKS) translate([s[0], s[1], -BIG / 2]) cylinder(d = STICK_HOLE_D, h = BIG); stick_screws() translate([0, 0, -BIG / 2]) cylinder(d = STICK_SCREW_D, h = BIG); // switch translate(SWITCH_POS) { translate([-SWITCH_SLOT[0] / 2, -SWITCH_SLOT[1] / 2, -BIG / 2]) cube([SWITCH_SLOT[0], SWITCH_SLOT[1], BIG]); for (m = [-1, 1]) translate([m * SWITCH_PITCH / 2, 0, -BIG / 2]) cylinder(d = SWITCH_HOLE_D, h = BIG); } // inserts for (s = SCREWS) translate([s[0], s[1], Z_SPLIT - 1]) cylinder(d = INSERT_D, h = 1 + INSERT_L); translate([0, 0, -ENGRAVE_D]) lx(1 + ENGRAVE_D) top_inlay_2d(); // ON/OFF and honeycomb inlays for (m = [-1, 1]) translate([HOOK_POS[0] + m * HOOK_INSERTS, HOOK_POS[1], -PLATE - 7]) { cylinder(d = INSERT_D, h = 7 + PLATE - 1); cylinder(d = SCREW_D, h = BIG); } } // ON/OFF text, cut into the top face and printed as a second-colour inlay // (PART = "inlay", exported in the same frame as PART = "top"). module switch_text_2d() for (t = [["ON", -1], ["OFF", 1]]) translate([t[1] * 19, 0]) text(t[0], size = 5, halign = "center", valign = "center", font = "Liberation Sans:style=Bold"); // Honeycomb on the right of a diagonal through the middle of the top face. // Only whole cells are drawn (every wall full width): a cell is kept when its // outer edge lies right of the diagonal, inside the top face (EDGE_KEEP from // the outline) and clear of the display window, the stick covers, the strap // eyelet (with its travel) and the switch with its ON/OFF text. HEX_R = 4.5; // cell circumradius (wall centre lines) HEX_LINE = 1.2; // wall width (3 extrusion widths) DIAG_POINT = [0, -14]; // the diagonal passes through here... DIAG_ANGLE = 20; // ...leaning this far from the v axis (top end to the right) EDGE_KEEP = 3; // from the outline (clear of the top chamfer) HEX_GAP = 1.5; // around the keep-outs HEX_OUT = (HEX_R + HEX_LINE / 2 / cos(30)); // outer circumradius of a cell // The outline is the hull of rounded boxes with one corner radius, so it is // this convex polygon grown by CORNER_R (corners listed counter-clockwise). function _ol_pts() = let(r = CORNER_R, f = FRONT_BAND, b = REAR_BAND, su = STICKS[1][0] + STICK_SQ[0] - r, sv = STICK_SQ[1] - r) [[f[0][0] + r, f[1][1] - r], [-su, sv], [-su, -sv], [b[0][0] + r, b[0][1] + r], [b[1][0] - r, b[0][1] + r], [su, -sv], [su, sv], [f[1][0] - r, f[1][1] - r]]; function _cross(a, b, q) = (b[0] - a[0]) * (q[1] - a[1]) - (b[1] - a[1]) * (q[0] - a[0]); function _seg_dist(a, b, q) = let(d = b - a, t = max(0, min(1, ((q - a) * d) / (d * d)))) norm(q - (a + t * d)); function _poly_dist(P, q) = let(n = len(P), inside = min([for (i = [0 : n - 1]) _cross(P[i], P[(i + 1) % n], q)]) >= 0) inside ? 0 : min([for (i = [0 : n - 1]) _seg_dist(P[i], P[(i + 1) % n], q)]); function _in_face(q) = _poly_dist(_ol_pts(), q) <= CORNER_R - EDGE_KEEP; function _right(q) = ((q - DIAG_POINT) * [cos(DIAG_ANGLE), -sin(DIAG_ANGLE)]) >= 0; function _rect_dist(c, size, q) = let(d = [max(abs(q[0] - c[0]) - size[0] / 2, 0), max(abs(q[1] - c[1]) - size[1] / 2, 0)]) norm(d); function _clear(q) = let(rr = HEX_OUT + HEX_GAP) _rect_dist(NX_WIN, NX_WINDOW + [2, 2] * NX_BEZEL, q) >= rr && min([for (st = STICKS) norm(q - st)]) >= 53.5 / 2 + rr && _rect_dist(HOOK_POS, [HOOK_BASE[0], HOOK_BASE[1] + 2 * HOOK_TRAVEL], q) >= rr && _rect_dist(SWITCH_POS, [2 * 19 + 16, 7], q) >= rr; function _cell_ok(c) = _clear(c) && min([for (k = [0 : 5]) let(q = c + HEX_OUT * [cos(60 * k), sin(60 * k)]) (_right(q) && _in_face(q)) ? 1 : 0]) == 1; HEX_CELLS = [for (i = [-30 : 30], j = [-20 : 20]) let(c = [i * 1.5 * HEX_R, (j + (i % 2 == 0 ? 0 : 0.5)) * sqrt(3) * HEX_R]) if (_cell_ok(c)) c]; // drop stray cells (fewer than 2 neighbours) HEX_KEEP = [for (c = HEX_CELLS) if (len([for (o = HEX_CELLS) if (o != c && norm(o - c) < 2 * HEX_R) 1]) >= 2) c]; module hex_pattern_2d() for (c = HEX_KEEP) translate(c) difference() { circle(r = HEX_OUT, $fn = 6); circle(r = HEX_R - HEX_LINE / 2 / cos(30), $fn = 6); } module top_inlay_2d() { translate(SWITCH_POS) switch_text_2d(); hex_pattern_2d(); } // Two inlays, so each can have its own colour (owner: black case, red // honeycomb, white ON/OFF). Each extra colour adds a swap on the first 3 layers. module hex_inlay() translate([0, 0, -ENGRAVE_D]) lx(ENGRAVE_D) hex_pattern_2d(); module text_inlay() translate([0, 0, -ENGRAVE_D]) lx(ENGRAVE_D) translate(SWITCH_POS) switch_text_2d(); // ---------- bottom shell ---------------------------------------------------- USBC_V = FRONT_V - 0.6; // receptacle front, 0.6 inside the front face module bottom_shell() render(convexity = 10) difference() { union() { difference() { intersection() { outer_solid(); translate([-BIG / 2, -BIG / 2, Z_BOT - 1]) cube([BIG, BIG, Z_SPLIT - Z_BOT + 1]); } inner_solid(); } // locating lip translate([0, 0, Z_SPLIT - 3]) lx(3 + LIP_H) difference() { offset(delta = -(T + FIT)) outline_2d(); offset(delta = -(T + FIT + LIP_W)) outline_2d(); for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT); } translate([0, 0, Z_SPLIT - 3]) lx(3) difference() { // ties the lip to the wall offset(delta = -(T - JOIN)) outline_2d(); offset(delta = -(T + FIT + LIP_W)) outline_2d(); for (s = SCREWS) translate(s) circle(d = BOSS_D + 2 * FIT); } intersection() { inner_solid(); union() { // screw towers for (s = SCREWS) translate([s[0], s[1], Z_BOT]) cylinder(d = BOSS_D, h = Z_SPLIT - Z_BOT); // bail pivot bosses in the side walls for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) cylinder(d = 10, h = 14); // UPS standoffs for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT]) cylinder(d = 6, h = UPS_Z - Z_BOT); // kickstand recess and hinge trough walls kickstand_housing(); // USB-C cradle usbc_cradle(); } } // main board standoffs intersection() { inner_solid(); perf_clamp_place() translate([0, 0, Z_BOT - PERF_Z]) cylinder(d = 8, h = PERF_Z - Z_BOT); } // front eyelet inserts: bosses behind the front wall intersection() { inner_solid(); for (m = [-1, 1]) translate([m * HOOK_INSERTS, FRONT_V - T - 6 + JOIN, HOOK_FRONT_Z]) rotate([-90, 0, 0]) cylinder(d = 8, h = 6 + JOIN); } } // screw holes: counterbore from below, clearance up to the split for (s = SCREWS) translate([s[0], s[1], 0]) { translate([0, 0, Z_BOT - 1]) cylinder(d = HEAD_D, h = HEAD_Z - Z_BOT + 1); cylinder(d = SCREW_D, h = BIG, center = true); } for (m = [-1, 1]) translate([UPS_CENTRE[0] + m * UPS_HOLES, UPS_CENTRE[1], Z_BOT + 1.2]) cylinder(d = 2.5, h = 20); for (l = UPS_LEDS) translate(concat(UPS_CENTRE + l, Z_BOT - 1)) lx(T + 2) hull() for (d = [-2, 2]) translate([0, d]) circle(d = 2); perf_clamp_place() translate([0, 0, -6]) cylinder(d = INSERT_D, h = 7); for (m = [-1, 1]) translate([m * HOOK_INSERTS, FRONT_V - INSERT_L - 1, HOOK_FRONT_Z]) rotate([-90, 0, 0]) cylinder(d = INSERT_D, h = INSERT_L + 2); kickstand_cut(); usbc_cut(); for (m = [-1, 1]) translate([m * SIDE_U, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([0, -m * 90, 0]) translate([0, 0, -1]) cylinder(d = INSERT_D, h = 1 + 8); } // Kickstand: a flap in a recess in the underside, hinged at the front on a // pin through a barrel. Friction on the pin holds the angle. KS_RECESS = KS_T + 0.5; KS_ROOF = Z_BOT + KS_RECESS + 2; // top of the recess roof KS_AXIS_Z = Z_BOT + KS_BARREL_D / 2 + 0.3; module kickstand_housing() { translate([-KS_W / 2 - FIT - KS_WALL, KS_V[0] - FIT - KS_WALL_V, Z_BOT]) cube([KS_W + 2 * (FIT + KS_WALL), KS_V[1] - KS_V[0] + KS_BARREL_D / 2 + 2 * FIT + 2 * KS_WALL_V, KS_RECESS + 2]); translate([-KS_W / 2 - FIT - KS_WALL, KS_V[1] - KS_BARREL_D / 2 - FIT - KS_WALL_V, Z_BOT]) cube([KS_W + 2 * (FIT + KS_WALL), KS_BARREL_D + 2 * (FIT + KS_WALL_V), KS_BARREL_D + 0.6 + FIT + 2]); } module kickstand_cut() { translate([-KS_W / 2 - FIT, KS_V[0] - FIT, Z_BOT - 1]) cube([KS_W + 2 * FIT, KS_V[1] - KS_V[0] + 2 * FIT, 1 + KS_RECESS]); translate([-KS_W / 2 - FIT, KS_V[1] - KS_BARREL_D / 2 - FIT, Z_BOT - 1]) cube([KS_W + 2 * FIT, KS_BARREL_D + 2 * FIT, 1 + KS_BARREL_D + 0.6 + FIT]); translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_PIN_D, h = KS_W + 2 * KS_WALL + 10, center = true); translate([KS_W / 2 + FIT + KS_WALL - 2.5, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) rotate([0, 0, 30]) cylinder(d = 5.5 / cos(30) + 0.3, h = 5, $fn = 6); } module kickstand() render(convexity = 10) difference() { union() { hull() { translate([-KS_W / 2, KS_V[0], Z_BOT]) cube([KS_W, 1, KS_T]); translate([-KS_W / 2, KS_V[1] - 1, Z_BOT]) cube([KS_W, 1, KS_T]); } translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_BARREL_D, h = KS_W, center = true); // finger notch lip at the free end is cut below } translate([0, KS_V[1], KS_AXIS_Z]) rotate([0, 90, 0]) cylinder(d = KS_PIN_D, h = KS_W + 2, center = true); translate([0, KS_V[0] - 2, Z_BOT - 1]) scale([1, 0.6, 1]) cylinder(r = 9, h = KS_T + 2); // finger notch } module perf_place() translate(concat(PERF_POS, PERF_Z)) rotate([0, 0, -90]) children(); // at each clamp post's axis, Z = 0 on the board's underside module perf_clamp_place() perf_place() for (c = PERF_CLAMPS) translate([c[0] + (c[0] > PERF[0] / 2 ? 1 : -1) * PERF_CLAMP_OUT, c[1], 0]) children(); module perf_clamp_screws() perf_clamp_place() translate([0, 0, PERF[2]]) color("#b0b0b0") { cylinder(d = 7, h = 0.5); // washer translate([0, 0, 0.5]) cylinder(d = 5.7, h = 1.65); // M3 button head } // USB-C breakout on a block, the receptacle in a slot through the front wall. module usbc_cradle() translate([USBC_POS[0] - USBC_BOARD[0] / 2 - 2, USBC_V - USBC_BOARD[1] - 2, Z_BOT]) cube([USBC_BOARD[0] + 4, USBC_BOARD[1] + 2 + 3, USBC_Z - Z_BOT]); module usbc_cut() { inner_v = FRONT_V - T; // board pocket (glue it in), open towards the inside; through the wall only the board's own slot translate([USBC_POS[0] - USBC_BOARD[0] / 2 - FIT, USBC_V - USBC_BOARD[1] - FIT, USBC_Z]) cube([USBC_BOARD[0] + 2 * FIT, inner_v - (USBC_V - USBC_BOARD[1] - FIT), 20]); translate([USBC_POS[0] - USBC_BOARD[0] / 2 - FIT, USBC_V - 5, USBC_Z]) cube([USBC_BOARD[0] + 2 * FIT, 5 + FIT, USBC_BOARD[2] + 2 * FIT]); // receptacle opening, chamfered on the outside for the plug translate([USBC_POS[0], USBC_V - 3, USBC_Z + USBC_BOARD[2] + USBC_RCPT[2] / 2]) rotate([-90, 0, 0]) { linear_extrude(10) offset(r = 1.4) square([USBC_RCPT[0] + 0.6 - 2.8, USBC_RCPT[2] + 0.6 - 2.8], center = true); translate([0, 0, 3 + 0.6 - 0.01]) linear_extrude(1.01, scale = [1.3, 1.6]) offset(r = 1.4) square([USBC_RCPT[0] + 0.6 - 2.8, USBC_RCPT[2] + 0.6 - 2.8], center = true); } } // Strap eyelet: printed base down (the d8 loop hole is a short bridge). module eyelet() render(convexity = 10) difference() { b = HOOK_BASE; union() { translate([-b[0] / 2, -b[1] / 2, 0]) cube(b); hull() { translate([-4, -b[1] / 2 + 2, 0]) cube([8, b[1] - 4, b[2]]); translate([-4, 0, HOOK_H - b[1] / 2 + 2]) rotate([0, 90, 0]) cylinder(r = b[1] / 2 - 2, h = 8); } } translate([-10, 0, HOOK_H - b[1] / 2 + 2]) rotate([0, 90, 0]) cylinder(d = HOOK_HOLE_D, h = 20); for (m = [-1, 1]) translate([m * HOOK_INSERTS, 0, -1]) hull() for (d = [-1, 1]) translate([0, d * HOOK_TRAVEL, 0]) cylinder(d = SCREW_D, h = 10); // screw heads (M3 button head, 5.7 mm) in slotted counterbores beside the loop for (m = [-1, 1]) translate([m * HOOK_INSERTS, 0, 2]) hull() for (d = [-1, 1]) translate([0, d * HOOK_TRAVEL, 0]) cylinder(d = 6.2, h = 10); } module eyelet_placed(shift = 0) translate([HOOK_POS[0], HOOK_POS[1] + shift, 0]) eyelet(); module eyelet_front_placed() translate([HOOK_POS[0], FRONT_V, HOOK_FRONT_Z]) rotate([-90, 0, 0]) eyelet(); // Brace bail, in its pivot frame: arms along +y (folded forward), pivots on x. BAIL_X = SIDE_U + BAIL_GAP; module bail() render(convexity = 10) difference() { union() { for (m = [-1, 1]) hull() for (y = [0, BAIL_L]) translate([m > 0 ? BAIL_X : -BAIL_X - BAIL_T, y, 0]) rotate([0, 90, 0]) cylinder(d = BAIL_H, h = BAIL_T); // crossbar, bowed outwards n = 16; w = BAIL_X + BAIL_T / 2; translate([0, 0, -BAIL_H / 2]) lx(BAIL_H) for (i = [0 : n - 1]) hull() for (k = [i, i + 1]) { x = -w + k * 2 * w / n; translate([x, BAIL_L + BAIL_BOW * (1 - pow(x / w, 2))]) circle(d = 8); } } rotate([0, 90, 0]) cylinder(d = SCREW_D, h = 2 * BIG, center = true); } module bail_placed() translate([0, BAIL_PIVOT[0], BAIL_PIVOT[1]]) rotate([BAIL_ANGLE, 0, 0]) bail(); // ---------- reference parts (local frames, then placed) --------------------- module nextion() { translate(concat(NX_CENTRE, NX_BOARD_TOP - 1.6)) color("#1e5a2a") difference() { translate(concat(-NX_BOARD / 2, 0)) cube(concat(NX_BOARD, 1.6)); for (du = [-1, 1], dv = [-1, 1]) translate([du * NX_HOLES[0], dv * NX_HOLES[1], 0] / 2 + [0, 0, -1]) cylinder(d = 3.2, h = 4); } translate(concat(NX_WIN - NX_LCD / 2, NX_BOARD_TOP)) color("#202020") cube(concat(NX_LCD, NX_LCD_T)); translate(concat(NX_WIN - [73.44, 48.96] / 2, -NX_BEZEL - 0.2)) color("#3050a0") cube([73.44, 48.96, 0.2]); translate(concat(NX_CENTRE + [(NX_FLIP ? 1 : -1) * (NX_BOARD[0] / 2 - 7), -5], NX_BOARD_TOP - 1.6 - 6)) color("#eee") cube([6, 10, 6]); // J1 4-pin connector (approx.) } module ups_18650() translate(concat(UPS_CENTRE, UPS_Z)) { color("#202020") difference() { translate([-89 / 2, -22 / 2, 0]) cube([89, 22, 1.6]); for (m = [-1, 1]) translate([m * UPS_HOLES, 0, -1]) cylinder(d = 3, h = 4); } color("#151515") translate([-77 / 2, -21 / 2, 1.6]) difference() { cube([77, 21, 22.4 - 1.6]); translate([3, 1.5, 3]) cube([71, 18, 30]); } color("#4060c0") translate([-65 / 2, 0, 1.6 + 3 + 18.5 / 2]) rotate([0, 90, 0]) cylinder(d = 18.5, h = 65); color("#b0b0b0") translate([89 / 2 - 7, -4.5, 1.6]) cube([7.5, 9, 3.2]); // Type-C (charge input) color("#808080") translate([89 / 2 + 0.5, -6, 0]) cube([18, 12, 7]); // cut-cable plug (approx.) } // Main board as in the owner's photos (layout approximate). module main_board() { perf_clamp_screws(); main_board_only(); } module main_board_only() perf_place() { color("#2a8a4a") difference() { cube(PERF); } // Teensy 4.0 in female headers (8.5 mm), micro-USB at the board edge translate([12.1, 1, PERF[2]]) { color("#111") for (x = [0, 17.8 - 2.5]) translate([x, 0, 0]) cube([2.5, 35.6, 8.5]); translate([0, 0, 8.5]) { color("#1e5a2a") cube([17.8, 35.6, 1.6]); color("#222") translate([4, 12, 1.6]) cube([10, 10, 1.2]); color("#c0c0c0") translate([(17.8 - 7.5) / 2, -1, 1.6]) cube([7.5, 5.7, 2.9]); color("#808080") translate([(17.8 - 10) / 2, -1 - 18, 1.6 - 2]) cube([10, 18, 7]); // cable plug (approx.) } } // nRF24L01 lying over the far edge, on its 2 x 4 header translate([15, 63, PERF[2]]) { color("#111") translate([2, 0, 0]) cube([10, 5, 2.5]); color("#151515") translate([0, 0, 2.5]) cube([15.3, 29, 1.2]); } color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117 // ribbon and display/IMU connectors at the edge, plugs on top (approx.) color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]); color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]); } // GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along) module imu_gy521() perf_place() translate(concat(PERF_IMU, PERF[2])) { color("#111") translate([0, 1, 0]) cube([2.5, 19, 8.5]); translate([0, 0, 8.5]) { color("#1f4fa0") cube([15.6, 21.2, 1.6]); color("#222") translate([6, 8.6, 1.6]) cube([4, 4, 1]); } } module usbc_breakout() translate([USBC_POS[0], USBC_V, USBC_Z]) { color("#1a7a3a") translate([-USBC_BOARD[0] / 2, -USBC_BOARD[1], 0]) cube(USBC_BOARD); color("#c0c0c0") translate([-USBC_RCPT[0] / 2, -USBC_RCPT[1], USBC_BOARD[2]]) cube(USBC_RCPT); } // Slide switch as on the old remote: mounting plate on the top face, screwed // down with 2 screws, body hanging through the slot. Sizes approximate. module slide_switch() translate(SWITCH_POS) color("#303030") { translate([-12.5, -3.5, 0]) cube([25, 7, 0.8]); // mounting plate translate([-7.5, -3.5, -10]) cube([15, 7, 10]); // body, through the slot translate([-1.5, -1.5, 0.8]) cube([3, 3, 4]); // knob } // JH-D300X-R1 3-axis joystick (owner's drawing): handle d35 with the twist // pot inside, dust cover d53.5 on top of the plate, 40.4 mm control box // (25.5 tall) under it, clamping the plate with 4 x M2.5 x 14. X/Y pots // d16.5 sticking 9.2 out of the box on -x and -y. Local Z = 0 on the cover's // underside (the top face); the box hangs from the plate's underside. JOY_BOX = 40.4; JOY_BOX_H = 25.5; JOY_POT_D = 16.5; JOY_POT_L = 49.6 - 40.4; JOY_COVER_T = 3.8; JOY_POT_Z = 15.3; // pot axis above the box bottom (from the drawing) module jh_d300x() { zb = -PLATE - JOY_BOX_H; // box bottom color("#202020") { difference() { cylinder(d1 = 53.5, d2 = 50, h = JOY_COVER_T); for (du = [-1, 1], dv = [-1, 1]) translate([du * STICK_SCREW, dv * STICK_SCREW, -1]) cylinder(d = 2.7, h = 6); } translate([0, 0, JOY_COVER_T]) cylinder(d = 39.5, h = 1); // dust ring translate([-JOY_BOX / 2, -JOY_BOX / 2, zb]) cube([JOY_BOX, JOY_BOX, JOY_BOX_H]); translate([0, 0, zb + JOY_POT_Z]) { rotate([0, -90, 0]) translate([0, 0, JOY_BOX / 2]) cylinder(d = JOY_POT_D, h = JOY_POT_L); // Y pot, -x rotate([90, 0, 0]) translate([0, 0, JOY_BOX / 2]) cylinder(d = JOY_POT_D, h = JOY_POT_L); // X pot, -y } t = JOY_COVER_T; translate([0, 0, t]) cylinder(d = 6, h = 11.5); // shaft translate([0, 0, t + 11]) cylinder(d1 = 12, d2 = 18, h = 8); // neck translate([0, 0, t + 19]) cylinder(d = 32, h = 7); translate([0, 0, t + 26]) cylinder(d = 35, h = 19); // knurled grip translate([0, 0, t + 45]) cylinder(d1 = 35, d2 = 30, h = 8); // top: 53 above the cover } } // pots towards the middle and towards the user module sticks() for (s = STICKS) translate(concat(s, 0)) if (s[0] > 0) jh_d300x(); else mirror([1, 0, 0]) jh_d300x(); module electronics() { nextion(); ups_18650(); main_board(); imu_gy521(); usbc_breakout(); slide_switch(); } // ---------- assembly and print layout -------------------------------------- module kickstand_placed() translate([0, KS_V[1], KS_AXIS_Z]) rotate([KS_OPEN, 0, 0]) translate([0, -KS_V[1], -KS_AXIS_Z]) kickstand(); module remote_v2() { if (SHOW_BOTTOM) { color("#1c1c1c") bottom_shell(); color("#1c1c1c") kickstand_placed(); color("#1c1c1c") bail_placed(); } if (HOOK_MOUNT == "front") color("#1c1c1c") eyelet_front_placed(); else if (SHOW_TOP) translate([0, 0, EXPLODE]) color("#1c1c1c") eyelet_placed(); if (SHOW_TOP) translate([0, 0, EXPLODE]) { color("#262626") top_shell(); color("#c8102e") hex_inlay(); color("#f2f2f2") text_inlay(); } if (SHOW_PARTS) { translate([0, 0, EXPLODE]) { nextion(); slide_switch(); } ups_18650(); main_board(); imu_gy521(); usbc_breakout(); } if (SHOW_STICKS) translate([0, 0, EXPLODE]) sticks(); } if (PART == "assembly") remote_v2(); else if (PART == "top") rotate([180, 0, 0]) top_shell(); // face down on the bed else if (PART == "inlay") rotate([180, 0, 0]) hex_inlay(); // load with "top" (and "text") as one multi-part object else if (PART == "text") rotate([180, 0, 0]) text_inlay(); else if (PART == "bottom") translate([0, 0, -Z_BOT]) bottom_shell(); else if (PART == "kickstand") translate([0, 0, -Z_BOT]) kickstand(); else if (PART == "eyelet") eyelet(); // base on the bed, the loop hole bridges else if (PART == "bail") translate([0, 0, BAIL_H / 2]) bail();