# Nextion HMI `remote.HMI` in this folder is the touchscreen project (NX4832T035, 480×320), turned 180° (Editor display direction 270) because the display sits upside down in the remote. It's **generated** by `../scripts/make_remote_hmi.py`: change the layout there and re-run it, rather than editing the `.HMI` in Nextion Editor (an Editor edit is lost on the next run). Then open `remote.HMI` in Nextion Editor, compile, and upload the `.tft`: SETUP › UPDATE DISPLAY (tap twice) or serial key `U` puts the remote in USB passthrough for the upload. ``` python scripts\make_remote_hmi.py (from 2026-current) ``` It needs the `tools/nextion-hmi-tools` submodule, Pillow, DejaVu Sans Mono (found in matplotlib, or `--font-dir`), and the old remote HMI (`../../2019-teensy-nrf24/remote-nextion/remote.HMI`, read only) for the splash picture. To look at a page without the Editor, use the `nxhmi` MCP server's `render_page`. ## Pages | id | Page | Contents | |----|------|----------| | 0 | `splash` | spider picture, 1.5 s, then `drive` | | 1 | `drive` | ARM, SIT/STAND, gait, mode, right-stick mode, both gyros, speed + height sliders, messages | | 2 | `status` | remote and robot IMU roll/pitch, the 6 stick axes, both batteries, radio | | 3 | `servos` | all 18 joint angles (robot telemetry), laid out as a top view of the robot | | 4 | `cal` | servo centre calibration: START/STOP, leg and joint, trim ±1/±10 µs, ZERO, REVERT, SAVE | | 5 | `setup` | stick calibration, LEVEL REMOTE, UPDATE DISPLAY, backlight, versions | | 6 | `upload` | shown during display update mode | Pages 1–5 share a frame: a top bar (`tLink` link quality, `tState` robot state + battery, red `bKill` DISARM) and tab buttons `bTab0`–`bTab4` that switch pages locally (`page drive`, ...). The page order is the page id, and must match `UiPage` in `UiTypes.h`. ## How the firmware talks to it - **Display → remote:** every touch sends a custom frame with `printh`: `'#'` (0x23), length, command byte, optional value byte. "Send Component ID" is off everywhere. - **Page tracking:** each page's Preinitialize event sends `'P'` + its page id, so the remote always knows which page is showing. After a remote restart it asks with `sendme`. - **Remote → display:** the remote writes only the showing page, by local component name (no `vscope = global`, no display RAM spent), and only what changed (`NextionUI` hashes every instruction). Everything is re-sent every 2 s and after the display restarts (0x88), so a dropped byte heals itself. Render rate is 20 Hz (SERVOS 10 Hz), and a render is skipped rather than blocking when the TX buffer is full. - **The remote is authoritative:** plain buttons only, nothing toggles locally. Exceptions that are purely local: the tabs, and the backlight slider (`dim` / `dims`). - `Program.s` sets `bauds=115200` (= `NEXTION_BAUD` in `Config.h`), stored in the display. ## Commands (display → remote) | Component | Event code | Command | |-----------|-----------|---------| | every page | `printh 23 02 50 ` (Preinitialize) | `P` page shown | | `bKill` | `printh 23 01 4B` | `K` disarm, always accepted | | `bArm` | `printh 23 01 41` | `A` toggle arm (needs sticks centered) | | `bStand` | `printh 23 01 53` | `S` toggle sit/stand | | `bGait` | `printh 23 01 47` | `G` tripod ↔ wave | | `bMode` | `printh 23 01 4D` | `M` direct ↔ heading-hold | | `bRs` | `printh 23 01 58` | `X` right stick rotate ↔ translate | | `bRGyro` | `printh 23 01 52` | `R` remote-gyro tilt on/off | | `bBGyro` | `printh 23 01 42` | `B` robot self-stabilize on/off | | `hSpeed` | `printh 23 02 56` + `prints hSpeed.val,1` (move + release) | `V` + speed 0..255 | | `hHeight` | `printh 23 02 48` + `prints hHeight.val,1` (move + release) | `H` + height 0..200, 100 = default | | `bCal` | `printh 23 01 43` | `C` start / save stick calibration | | `bCalX` | `printh 23 01 51` | `Q` cancel stick calibration | | `bZero` | `printh 23 01 5A` | `Z` zero handset level | | `bUpd` | `printh 23 01 55` | `U` display update mode (second tap within 3 s) | | `bCalOn` | `printh 23 01 4F` | `O` servo calibration start/stop | | `bL0`–`bL5` | `printh 23 02 4C 0n` | `L` + leg (0 FR, 1 MR, 2 RR, 3 RL, 4 ML, 5 FL) | | `bJ0`–`bJ2` | `printh 23 02 4A 0n` | `J` + joint (0 coxa, 1 femur, 2 tibia) | | `bM10` `bM1` `bP1` `bP10` `bZeroT` | `printh 23 02 54 0n` | `T` + trim step: 0 −10, 1 −1, 2 +1, 3 +10, 4 zero (µs) | | `bSave` | `printh 23 01 57` | `W` save trims on the robot | | `bRevert` | `printh 23 01 45` | `E` reload trims from the robot's EEPROM | To add a control: pick an unused command byte, add it to `NextionUI::decodeCustom()` and `UiCmd`, handle it in `RemoteState::handle()`, add the component in `make_remote_hmi.py`, and a row here. ## What the remote writes (remote → display) | Page | Components | |------|-----------| | all but splash/upload | `tLink` txt/pco, `tState` txt/pco | | drive | `bArm` `bStand` txt/bco, `bGait` `bMode` `bRs` txt, `bRGyro` `bBGyro` bco, `hSpeed` `hHeight` val, `tSpeed` `tHeight` `tMsg` txt | | status | `tRRoll` `tRPitch` `tBRoll` `tBPitch` txt, `hRRoll` `hRPitch` `hBRoll` `hBPitch` val (0..90 = ±45°), `hLX` `hLY` `hLT` `hRX` `hRY` `hRT` val (0..200 = ±1000), `tBatt` `tRadio` txt. The indicator sliders have touch switched off (`tsw` in Preinitialize) | | servos | `tJ0`–`tJ17` txt (index = leg × 3 + joint), `jJ0`–`jJ17` val (position in the servo's travel), `tSrv` txt/pco | | cal | `bCalOn` txt/bco, `bL0`–`bL5` `bJ0`–`bJ2` bco (selected = green), `tTrim` txt, `bSave` bco (orange = unsaved), `tMsg` txt | | setup | `bCal` txt/bco, `bUpd` txt/bco, `tVer` txt, `tMsg` txt | `txt_maxl` of each text is set in the generator to fit the longest string the firmware writes. Keep them in step when you change a format string.