Commit Graph
10 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 a59faf3b03 2026 docs: update the planned/future notes
- PLANNING.md: IMU on the pin headers is done; battery firmware is done
  except the % curve and the low-battery warning.
- README "Where to go next": link sim/README and dongle/README.
- remote/README intro: telemetry comes back; the sim can answer via the dongle.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:54:10 +01:00
mangavalkandClaude Opus 5.5 175a1a0da8 2026 docs: catch the READMEs up with today's state
- README: the HMI is generated turned round (nothing to set in the Editor);
  PC radio link: bridge mode done, no USB links any more, what's left
  (Unity driving the real robot, three nodes at once).
- remote/README checklist: sticks and IMU checked, display uploaded, radio
  checked against the sim through the dongle; replace the IMU board.
- CLAUDE.md: display runs the new HMI; next steps.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:52:44 +01:00
mangavalkandClaude Opus 5.5 aeccba3be7 2026 remote: wiring as found on the real remote, IMU reset fix
- Nextion is on Serial2 (pins 7/8) - already in the last commit; docs updated.
- MPU6050 on Wire (18/19) so everything is on the edge headers (owner's
  choice); the two stick wires from 18/19 move to A7/A8 (21/22).
- Stick mapping checked on the real remote: left stick X/Y/twist on
  A3/A7/A8, right on A0/A1/A2, all inverted but the right twist.
- RemoteIMU: full device reset before waking. The remote's MPU6050 (likely
  a clone) answers and wakes without it but every data register reads 0.
  Axis defaults confirmed (+pitch nose down, +roll right side down).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 22:03:08 +01:00
mangavalkandClaude Opus 5.5 0b836af8de 2026 remote: tabbed Nextion UI, robot telemetry, servo centre calibration
Protocol v4: CmdPacket grows to 26 bytes (cal_cmd, cal_servo, cal_value);
new 30-byte Telemetry rides back on the nRF24 ack payload (robot state,
IMU, battery, 18 joint angles, packets/s, servo-cal echo). Each end drops
wrong-length packets, so version mismatches still fail closed.

Robot (owner-approved): SERVO_CAL state while disarmed, per-servo centre
trims (+-200 us) in EEPROM, telemetry, battery reading; the IMU estimate
now always runs (leveling still gated by ROBOT GYRO).

Remote: generated HMI (scripts/make_remote_hmi.py) with pages splash,
drive, status, servos, cal, setup, upload; page-aware NextionUI that only
writes the showing page and only what changed; servo calibration and
UPDATE DISPLAY on the touchscreen and serial console; battery module.
The display is on Serial2 (pins 7/8), found on the real remote; the old
sketch's Serial1 was never connected to it.

Sim: RF24 shim supports ack payloads, API version 8
(hxsim_get_ack_payload); sim_smoke checks telemetry and every CAL command.
Unity CmdPacket mirror updated.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-17 14:42:37 +01:00
mangavalkandClaude Opus 5.5 60605209fb 2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.

- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
  with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
  and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
  stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 18:57:49 +01:00
mangavalkandClaude Opus 5.5 e23216b3a1 2026 remote: build for the Teensy 4.0 actually in the remote
Board teensy41 -> teensy40. All pins exist on the 4.0; the MPU6050's
Wire2 (SDA2 25 / SCL2 24) is on the underside solder pads.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 12:19:16 +01:00
mangavalk dfd4d34512 Fold LEGACY into the generation folders
The LEGACY copies of HexapodRobot, Hexapod_NEW, Hexapod_Teensy and the old remote sketch were identical to the imported repos and are removed. The old Nextion design moves to 2019-teensy-nrf24/remote-nextion/, the 2019 remote case files to 2019-teensy-nrf24/remote-case/. Paths in CLAUDE.md, READMEs, remote/ comments, sim/build.ps1, the Unity DLL message and .vscode/settings.json now point to the new places. robot/ is not touched (its CLAUDE.md asks to check with the owner first).
2026-10-25 17:30:35 +01:00
mangavalkandClaude Opus 5.5 a961fa721b Remote: match the old remote's hardware; old remote code in LEGACY
- LEGACY/remote/teensy/: old remote sketch from
  https://mangavalk.com/Hexapod/remote.git @ 492dece (reference only).
- remote/Config.h: sticks on A0-A5, Nextion on Serial1 (0/1), as in the
  old sketch; MPU6050 moved to Wire2 (25/24) since A4/A5 are Wire's pins.
- NextionUI: controls on a vscope-global "control" page added to the
  old HMI; keeps the old t1 status texts; the old page-1 b2 button (and
  serial 'U') enter Nextion upload passthrough, following the PC's baud.
- Docs: NEXTION.md, remote README wiring, CLAUDE.md.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-10-01 15:29:21 +02:00
mangavalkandClaude Opus 5.5 935526eab5 Firmware simulation, Unity project, and sim-verified robot fixes
Simulation
- sim/: the unchanged robot firmware compiled into hexapod_sim.dll
  against PC stand-ins (Arduino, Servo, Wire + register-level MPU6050,
  RF24 with matching-config radio), a kinematic body model (support
  plane + planted-foot odometry) that also drives the simulated IMU,
  and a headless smoke test (sim_smoke). build.ps1 builds and tests.
- Hexapod_Simulation_Unity/ folded in (history kept in a bundle
  outside the repo). Assets/HexapodSim loads the DLL, drives the
  existing leg rig, and offers joystick / keyboard / robot-serial
  input plus a test panel.

Robot (all found or confirmed in the simulation)
- Config.h geometry taken from the Unity model.
- IK femur elevation sign, gait stance direction, body pose
  rotation direction, yaw lever arm.
- Stance feet integrated from the current command; gait restarts at
  mid-stance; heading integrates the applied turn rate, only while
  walking.
- Leg clearance and reach checks (Limits::feetFeasible); walk command
  and body pose scaled as a whole, pose scale rate-limited, planted
  feet guarded so the body never snaps or legs collide.
- Robot-gyro self-leveling as an integrator.
- Heading mode: steering relative to the body; S walks backward.
- Standing height from the remote (STANCE_HEIGHT_RANGE_MM).

Protocol v3 (reflash both boards)
- CmdPacket gains body_height (22 bytes).

Remote
- Height slider (Nextion hHeight/nHeight, serial [ ]).
- Fixed unspecified I2C read order in RemoteIMU.

LEGACY/: owner's old Nextion HMI and remote hardware assets.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-09-29 00:37:12 +02:00
mangavalkandClaude Opus 5.5 91dac16fca Draft: shared protocol, remote firmware, project docs
Not yet verified on hardware.

- shared/HexapodProtocol: CmdPacket (now 20 bytes, adds remote_roll /
  remote_pitch), FLAG_* bits and radio settings as the single protocol
  definition; static payload size = sizeof(CmdPacket) on both radios.
- robot: use the shared protocol; vx = forward (harness w/x <-> q/e);
  InputMapper adds remote tilt on top of the right stick when
  FLAG_REMOTE_GYRO is set, and robot.ino no longer zeroes stick
  roll/pitch when it's off.
- remote (Teensy 4.1): Sticks (calibration, EEPROM), RemoteIMU,
  RemoteState (interlocks, link-loss disarm, smoothing), PacketBuilder,
  RadioLink, NextionUI, SerialConsole.
- CLAUDE.md, README.md, remote/README.md, remote/NEXTION.md.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-09-28 18:14:00 +02:00