- Bottom shell: the brace pivot bosses stand on pillars and the lip's tie
band steps out at 45 deg (both were floating overhangs); the kickstand
barrel sits on the bed. Checked by slicing the STLs layer by layer: only
bridges are left. STLs re-exported.
- remote_v2_top_multicolor.3mf: now the owner's OrcaSlicer project (all
parts on two plates); export_3mf.py regenerates the plain multi-part file.
- README "Planned": a USB nRF24 stick on the PC so Unity can talk to both
the robot and the remote (what to work out), plus pointers to the other
notes for later.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.
- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Board teensy41 -> teensy40. All pins exist on the 4.0; the MPU6050's
Wire2 (SDA2 25 / SCL2 24) is on the underside solder pads.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
hardware/openscad/ rebuilds the broken Fusion models as OpenSCAD:
body (top/bottom plate, standoffs, battery bay, switch), legs (coxa
bracket, femur link, tibia, horn adapters, TPU socks, servo cables),
the whole robot, and the remote (shell, lid, Nextion 3.5", JH-D400X-R4
sticks, 18650 UPS board, IMU, Teensy 4.0, USB-C breakout). Every part
was checked by slicing against the original STEP solids; the original's
bugs are fixed and listed in PLANNING.md.
The robot now uses a hexagon leg layout (corner legs 60 deg round from
the mid legs; the corner coxa brackets need turning on their splines).
Physical limits from a collision sweep of the model are in Config.h:
per-leg coxa limits and LEG_CLEARANCE_MM 56 (a leg is 55.2 mm wide at
the joints); the sim API exports them (version 7). sim_smoke passes.
Unity loads the model (export_unity.py -> Resources/OpenScadModel,
OpenScadModel.cs builds a new rig in place of the old scene's robot).
The PCB model's mounting holes now use the exact EasyEDA grid. README
shows renders of both.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The Teensy 3.6 carrier board mounted inside the robot body (Teensy
peeks through the top-body hole). Contents:
- PCB_test_2026-11-13.json : EasyEDA PCB source (editor v6.5.61).
- OBJ_test.obj + .mtl : EasyEDA 3D OBJ export (slab + holes only).
- top.png, bottom.png : EasyEDA renders of each side; bottom.png
is the authoritative source for the
JP1-JP7 silkscreen numbering.
- 20190524_234512.jpg : photo of the populated bottom side.
- 20190524_234518.jpg : photo of the top side, powered on.
- main-pcb.scad : parametric OpenSCAD reconstruction. Real
board outline, 4 M3 holes, and every major
component (Teensy 3.6, nRF24L01+, GY-521
IMU, 7805, ZENER, JP7 battery JST, six
JST-PH 2mm servo headers JP1-JP6, POWER
LED + 510R resistor, "Hexapod v1" silk) on
the correct side of the board. Placements
are the pad-group centres pulled from the
EasyEDA JSON, not eyeballed.
- README.md : explains the files, the EasyEDA format and
unit conversion, which side each part is
on, and an authoritative placement table.
Co-Authored-By: Claude Opus 4.7 <noreply@anthropic.com>
Body bottom, bottom and mid leg, servo horn (v5 and v6), Hitec HS-485HB servo model and the remote case (v4 and v40), with their preview images and exports. From D:\Fusion 360 export.