Commit Graph
4 Commits
Author SHA1 Message Date
mangavalkandClaude Opus 5.5 0f9655d646 2026 remote v2: add the generated top-shell + inlays 3MF
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 22:12:12 +01:00
mangavalkandClaude Opus 5.5 4aeb79dc89 2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF
- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by
  4 side clamps (M3 button head + washer into inserts), no holes in the board
- export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb +
  ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the
  owner's OrcaSlicer project
- STLs re-exported, README printing table and PLANNING notes updated

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 22:12:02 +01:00
mangavalkandClaude Opus 5.5 80270ba17e 2026 remote v2: printable bottom shell, notes for the PC radio link
- Bottom shell: the brace pivot bosses stand on pillars and the lip's tie
  band steps out at 45 deg (both were floating overhangs); the kickstand
  barrel sits on the bed. Checked by slicing the STLs layer by layer: only
  bridges are left. STLs re-exported.
- remote_v2_top_multicolor.3mf: now the owner's OrcaSlicer project (all
  parts on two plates); export_3mf.py regenerates the plain multi-part file.
- README "Planned": a USB nRF24 stick on the PC so Unity can talk to both
  the robot and the remote (what to work out), plus pointers to the other
  notes for later.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 19:13:28 +01:00
mangavalkandClaude Opus 5.5 60605209fb 2026: remote v2 (flat console for the twist-grip sticks), STL/3MF exports, archive page
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.

- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
  with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
  and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
  stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
2026-11-14 18:57:49 +01:00