The old HMI's pages are 0 splashsceen, 1 main, 2 servocal, 3 page0,
4 uploadscreen, 5 joysticks; the link-status texts are main.t1 and
page0.t1 (not page1.t1/page3.t1, which the display silently ignored).
remote.HMI is the 2019 project re-saved by Nextion Editor 1.68, to work
on here instead of in 2019-teensy-nrf24/.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
remote_v2.scad: a new remote for the same electronics, 216 x 116 x 32 mm,
ASA, two shells printed without supports and joined with M3 heat-set
inserts. Hangs level from a neck strap on a balance-point eyelet (top face
or front edge) with a fold-out body brace; kickstand for the table.
JH-D300X-R1 sticks clamp the plate; main perfboard (Teensy 4.0, nRF24,
IMU) clamped at its sides under the display; UPS board with its LEDs
through the floor. Red honeycomb and white ON/OFF inlays in the first
3 layers. Every part checked for collisions.
- stl/remote_v2/: print-ready STLs, plus a multi-part 3MF (export_3mf.py)
with the inlays on filaments 2 and 3
- ARCHIVE.md: the original remote with the owner's photos; README shows v2
and how to print it
- Notes for later: battery-voltage reading, IMU on Wire (18/19) with two
stick axes moved to A7/A8, a stable 6 V supply for the 18 servos
- remote.scad: its sticks are JH-D300X-R1 (the model uses the D400X drawing)
- *.3mf through Git LFS; repo README says Teensy 4.0 remote
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Board teensy41 -> teensy40. All pins exist on the 4.0; the MPU6050's
Wire2 (SDA2 25 / SCL2 24) is on the underside solder pads.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
The LEGACY copies of HexapodRobot, Hexapod_NEW, Hexapod_Teensy and the old remote sketch were identical to the imported repos and are removed. The old Nextion design moves to 2019-teensy-nrf24/remote-nextion/, the 2019 remote case files to 2019-teensy-nrf24/remote-case/. Paths in CLAUDE.md, READMEs, remote/ comments, sim/build.ps1, the Unity DLL message and .vscode/settings.json now point to the new places. robot/ is not touched (its CLAUDE.md asks to check with the owner first).
- LEGACY/remote/teensy/: old remote sketch from
https://mangavalk.com/Hexapod/remote.git @ 492dece (reference only).
- remote/Config.h: sticks on A0-A5, Nextion on Serial1 (0/1), as in the
old sketch; MPU6050 moved to Wire2 (25/24) since A4/A5 are Wire's pins.
- NextionUI: controls on a vscope-global "control" page added to the
old HMI; keeps the old t1 status texts; the old page-1 b2 button (and
serial 'U') enter Nextion upload passthrough, following the PC's baud.
- Docs: NEXTION.md, remote README wiring, CLAUDE.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Simulation
- sim/: the unchanged robot firmware compiled into hexapod_sim.dll
against PC stand-ins (Arduino, Servo, Wire + register-level MPU6050,
RF24 with matching-config radio), a kinematic body model (support
plane + planted-foot odometry) that also drives the simulated IMU,
and a headless smoke test (sim_smoke). build.ps1 builds and tests.
- Hexapod_Simulation_Unity/ folded in (history kept in a bundle
outside the repo). Assets/HexapodSim loads the DLL, drives the
existing leg rig, and offers joystick / keyboard / robot-serial
input plus a test panel.
Robot (all found or confirmed in the simulation)
- Config.h geometry taken from the Unity model.
- IK femur elevation sign, gait stance direction, body pose
rotation direction, yaw lever arm.
- Stance feet integrated from the current command; gait restarts at
mid-stance; heading integrates the applied turn rate, only while
walking.
- Leg clearance and reach checks (Limits::feetFeasible); walk command
and body pose scaled as a whole, pose scale rate-limited, planted
feet guarded so the body never snaps or legs collide.
- Robot-gyro self-leveling as an integrator.
- Heading mode: steering relative to the body; S walks backward.
- Standing height from the remote (STANCE_HEIGHT_RANGE_MM).
Protocol v3 (reflash both boards)
- CmdPacket gains body_height (22 bytes).
Remote
- Height slider (Nextion hHeight/nHeight, serial [ ]).
- Fixed unspecified I2C read order in RemoteIMU.
LEGACY/: owner's old Nextion HMI and remote hardware assets.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Not yet verified on hardware.
- shared/HexapodProtocol: CmdPacket (now 20 bytes, adds remote_roll /
remote_pitch), FLAG_* bits and radio settings as the single protocol
definition; static payload size = sizeof(CmdPacket) on both radios.
- robot: use the shared protocol; vx = forward (harness w/x <-> q/e);
InputMapper adds remote tilt on top of the right stick when
FLAG_REMOTE_GYRO is set, and robot.ino no longer zeroes stick
roll/pitch when it's off.
- remote (Teensy 4.1): Sticks (calibration, EEPROM), RemoteIMU,
RemoteState (interlocks, link-loss disarm, smoothing), PacketBuilder,
RadioLink, NextionUI, SerialConsole.
- CLAUDE.md, README.md, remote/README.md, remote/NEXTION.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>