2026 docs: update the planned/future notes
- PLANNING.md: IMU on the pin headers is done; battery firmware is done except the % curve and the low-battery warning. - README "Where to go next": link sim/README and dongle/README. - remote/README intro: telemetry comes back; the sim can answer via the dongle. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
175a1a0da8
commit
a59faf3b03
3 files changed
+16
-8
No files matched your search
@@ -110,7 +110,11 @@ Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/o
|
||||
robot without a remote.
|
||||
- **[remote/README.md](remote/README.md)**: wiring, control scheme, stick
|
||||
calibration, and the remote's serial console.
|
||||
- **[remote/NEXTION.md](remote/NEXTION.md)**: how to build the touchscreen
|
||||
HMI.
|
||||
- **[remote/NEXTION.md](remote/NEXTION.md)**: the touchscreen HMI (generated
|
||||
by `scripts/make_remote_hmi.py`).
|
||||
- **[sim/README.md](sim/README.md)**: the robot firmware in simulation, headless
|
||||
and in Unity, with the keyboard or the real remote over the radio.
|
||||
- **[dongle/README.md](dongle/README.md)**: the USB nRF24 stick, its firmware,
|
||||
flashing and the bridge protocol.
|
||||
- **[shared/HexapodProtocol/HexapodProtocol.h](shared/HexapodProtocol/HexapodProtocol.h)**:
|
||||
the protocol. Change it only by reflashing both boards.
|
||||
@@ -213,15 +213,17 @@ charge/on LEDs show through two slots in the floor.
|
||||
for the stall current. The battery must also fit the bay (see open
|
||||
question 3) and leave room for the servo plugs.
|
||||
|
||||
- Remote: connect the IMU to the normal pin headers instead of the Teensy
|
||||
4.0's underside pads; see `remote/README.md`, "Planned" (Wire on 18/19,
|
||||
the two stick axes there move to A7/A8).
|
||||
- Remote: the IMU is on the normal pin headers (done 2026-11-17: Wire on
|
||||
18/19, the two stick axes that were there moved to A7/A8; display on
|
||||
Serial2, 7/8). Pinout in `remote/README.md`, "Wiring".
|
||||
|
||||
- Remote: measure the 18650's voltage on the Teensy to show how much charge
|
||||
is left (owner, later). Divider ~100k/100k from the cell's + (holder or the
|
||||
UPS board's B+, not the 5 V output) to A6 (pin 20, free), 100 nF to GND;
|
||||
full cell = ~2.1 V at the pin. Firmware: average, Li-ion curve to %, show
|
||||
on the Nextion with a low-battery warning (optionally send it to the robot).
|
||||
full cell = ~2.1 V at the pin. Firmware: reading, smoothing and the volts
|
||||
on the STATUS page are done (`remote/Battery`, pin still 255 = not wired);
|
||||
still to do: Li-ion curve to %, and a low-battery warning. The robot
|
||||
already sends its own battery voltage back in the telemetry.
|
||||
|
||||
- Servo wires barely fit on the real robot: the six servo headers hang
|
||||
above the battery bay, and the front pair sits right over the bay's end
|
||||
|
||||
@@ -4,7 +4,9 @@ Handheld transmitter for the hexapod. It reads two 3-axis twist-grip
|
||||
joysticks and an MPU6050, takes operator commands from a Nextion
|
||||
touchscreen, and sends a `CmdPacket` (defined in
|
||||
`../shared/HexapodProtocol/HexapodProtocol.h`) to the robot over nRF24L01
|
||||
at 100 Hz.
|
||||
at 100 Hz. The robot's `Telemetry` comes back in the radio's ack payloads.
|
||||
Without the robot, the Unity simulation can answer instead, through the
|
||||
USB nRF24 dongle (`../sim/README.md`).
|
||||
|
||||
## Planned
|
||||
|
||||
|
||||
Reference in new issue
Block a user