2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF
- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by 4 side clamps (M3 button head + washer into inserts), no holes in the board - export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb + ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the owner's OrcaSlicer project - STLs re-exported, README printing table and PLANNING notes updated Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
80270ba17e
commit
4aeb79dc89
6 files changed
+22
-16
No files matched your search
@@ -54,8 +54,9 @@ Regenerate them from `remote_v2.scad` with `-D 'PART="..."'`.
|
|||||||
|
|
||||||
| File | Part | Notes |
|
| File | Part | Notes |
|
||||||
|------|------|-------|
|
|------|------|-------|
|
||||||
| `remote_v2_top_multicolor.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
|
| `remote_v2_top_inlays.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
|
||||||
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
|
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
|
||||||
|
| `remote_v2_top_multicolor.3mf` | OrcaSlicer project (owner) | all parts on two plates; after re-exporting STLs, update its parts with Orca's "Reload from disk" |
|
||||||
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
|
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
|
||||||
| `remote_v2_kickstand.stl` | table stand | |
|
| `remote_v2_kickstand.stl` | table stand | |
|
||||||
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
|
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
|
||||||
@@ -91,7 +92,12 @@ Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/o
|
|||||||
robot and nothing comes back. Three nodes need an address per node (or
|
robot and nothing comes back. Three nodes need an address per node (or
|
||||||
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
|
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
|
||||||
or in time slots) so the nodes don't talk over each other; who has
|
or in time slots) so the nodes don't talk over each other; who has
|
||||||
priority when the PC and the remote both send commands;
|
priority when the PC and the remote both send commands. Owner's
|
||||||
|
decisions: the remote wins, with a toggle on the remote that hands the
|
||||||
|
robot to Unity and lets the remote's sticks control Unity instead; the
|
||||||
|
PC is the hub while it's online, the robot is the hub when it isn't;
|
||||||
|
goals: mirror the real robot in Unity, drive it from Unity, remote data
|
||||||
|
to the PC, and PC data to the remote;
|
||||||
- Unity side: a serial-port reader/writer next to the simulation (the
|
- Unity side: a serial-port reader/writer next to the simulation (the
|
||||||
2019 generation already drove the robot from Unity, through the remote
|
2019 generation already drove the robot from Unity, through the remote
|
||||||
over USB: see `../2019-teensy-nrf24/`).
|
over USB: see `../2019-teensy-nrf24/`).
|
||||||
|
|||||||
@@ -145,7 +145,7 @@ them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
|
|||||||
inlay (owner preferred a honeycomb).
|
inlay (owner preferred a honeycomb).
|
||||||
|
|
||||||
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
|
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
|
||||||
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01
|
sits socketed on a cut perfboard (56 x 80, measured) with the nRF24L01
|
||||||
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
|
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
|
||||||
switch's plate sits on top of the case, body through the slot, and the old
|
switch's plate sits on top of the case, body through the slot, and the old
|
||||||
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
||||||
@@ -197,7 +197,7 @@ charge/on LEDs show through two slots in the floor.
|
|||||||
- Checked: no part collides with the shells or with each other, the shells
|
- Checked: no part collides with the shells or with each other, the shells
|
||||||
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
||||||
from 0 to -180 deg (CGAL intersections).
|
from 0 to -180 deg (CGAL intersections).
|
||||||
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS
|
- Open: component positions on the main board, Teensy cable plug size, LCD thickness, UPS
|
||||||
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
|
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
|
||||||
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
|
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
|
||||||
|
|
||||||
|
|||||||
@@ -2,7 +2,7 @@
|
|||||||
|
|
||||||
python export_3mf.py (from hardware/openscad, after the STL export)
|
python export_3mf.py (from hardware/openscad, after the STL export)
|
||||||
|
|
||||||
Writes stl/remote_v2/remote_v2_top_multicolor.3mf: the top shell with its
|
Writes stl/remote_v2/remote_v2_top_inlays.3mf: the top shell with its
|
||||||
two inlays as ONE object with three parts, in the same frame, each part on
|
two inlays as ONE object with three parts, in the same frame, each part on
|
||||||
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
|
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
|
||||||
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
|
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
|
||||||
@@ -21,7 +21,7 @@ PARTS = [
|
|||||||
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
|
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
|
||||||
("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
|
("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
|
||||||
]
|
]
|
||||||
OUT = "remote_v2_top_multicolor.3mf"
|
OUT = "remote_v2_top_inlays.3mf" # remote_v2_top_multicolor.3mf is the owner's OrcaSlicer project
|
||||||
|
|
||||||
|
|
||||||
def read_stl(path):
|
def read_stl(path):
|
||||||
|
|||||||
@@ -94,14 +94,14 @@ UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
|
|||||||
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
|
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
|
||||||
|
|
||||||
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
|
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
|
||||||
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the
|
// Cut perfboard, 56 x 80 mm (owner). Component positions are estimates from the
|
||||||
// owner's photos: measure before printing. Board frame: x across (0..52), y
|
// owner's photos. Board frame: x across (0..56), y
|
||||||
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
|
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
|
||||||
PERF = [52, 80, 1.6];
|
PERF = [56, 80, 1.6]; // measured by the owner: 56 x 80
|
||||||
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
|
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
|
||||||
// beside the edge carries the board's edge on its inner half, and an M3 x 8
|
// beside the edge carries the board's edge on its inner half, and an M3 x 8
|
||||||
// button head with a washer (d7) in a heat-set insert in the post clamps it.
|
// button head with a washer (d7) in a heat-set insert in the post clamps it.
|
||||||
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y
|
PERF_CLAMPS = [[0, 4], [0, 68], [PERF[0], 4], [PERF[0], 68]]; // board frame: on the long edges x = 0 / PERF[0], at these y
|
||||||
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
|
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
|
||||||
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
|
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
|
||||||
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
|
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
|
||||||
@@ -493,8 +493,8 @@ module main_board_only() perf_place() {
|
|||||||
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
|
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
|
||||||
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
|
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
|
||||||
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
|
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
|
||||||
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]);
|
color("#333") translate([PERF[0] - 8, 8, PERF[2]]) cube([5, 21, 12]);
|
||||||
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]);
|
color("#333") translate([PERF[0] - 8, 44, PERF[2]]) cube([5, 11, 12]);
|
||||||
}
|
}
|
||||||
|
|
||||||
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)
|
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)
|
||||||
|
|||||||
Binary file not shown.
Binary file not shown.
Reference in new issue
Block a user