2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF

- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by
  4 side clamps (M3 button head + washer into inserts), no holes in the board
- export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb +
  ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the
  owner's OrcaSlicer project
- STLs re-exported, README printing table and PLANNING notes updated

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-14 22:12:02 +01:00
1 parent 80270ba17e
commit 4aeb79dc89
6 files changed
+22 -16

No files matched your search

+8 -2
View File
@@ -54,8 +54,9 @@ Regenerate them from `remote_v2.scad` with `-D 'PART="..."'`.
| File | Part | Notes | | File | Part | Notes |
|------|------|-------| |------|------|-------|
| `remote_v2_top_multicolor.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below | | `remote_v2_top_inlays.3mf` | top shell with both inlays | One object with three parts on filaments 1/2/3: case black, honeycomb red, ON/OFF white. The inlays are the first 3 layers (0.6 mm) of the face-down shell, so the colour swaps only happen there. Made by `hardware/openscad/export_3mf.py` from the three STLs below |
| `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object | | `remote_v2_top.stl` + `_inlay.stl` + `_text.stl` | the same, as STLs | Load the three at once and keep them as one multi-part object |
| `remote_v2_top_multicolor.3mf` | OrcaSlicer project (owner) | all parts on two plates; after re-exporting STLs, update its parts with Orca's "Reload from disk" |
| `remote_v2_bottom.stl` | bottom shell | flat underside on the bed | | `remote_v2_bottom.stl` | bottom shell | flat underside on the bed |
| `remote_v2_kickstand.stl` | table stand | | | `remote_v2_kickstand.stl` | table stand | |
| `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge | | `remote_v2_eyelet.stl` | neck-strap eyelet | on the top face (slots to balance it) or on the front edge |
@@ -91,7 +92,12 @@ Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/o
robot and nothing comes back. Three nodes need an address per node (or robot and nothing comes back. Three nodes need an address per node (or
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
or in time slots) so the nodes don't talk over each other; who has or in time slots) so the nodes don't talk over each other; who has
priority when the PC and the remote both send commands; priority when the PC and the remote both send commands. Owner's
decisions: the remote wins, with a toggle on the remote that hands the
robot to Unity and lets the remote's sticks control Unity instead; the
PC is the hub while it's online, the robot is the hub when it isn't;
goals: mirror the real robot in Unity, drive it from Unity, remote data
to the PC, and PC data to the remote;
- Unity side: a serial-port reader/writer next to the simulation (the - Unity side: a serial-port reader/writer next to the simulation (the
2019 generation already drove the robot from Unity, through the remote 2019 generation already drove the robot from Unity, through the remote
over USB: see `../2019-teensy-nrf24/`). over USB: see `../2019-teensy-nrf24/`).
+2 -2
View File
@@ -145,7 +145,7 @@ them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
inlay (owner preferred a honeycomb). inlay (owner preferred a honeycomb).
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01 sits socketed on a cut perfboard (56 x 80, measured) with the nRF24L01
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the (100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
switch's plate sits on top of the case, body through the slot, and the old switch's plate sits on top of the case, body through the slot, and the old
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's 8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
@@ -197,7 +197,7 @@ charge/on LEDs show through two slots in the floor.
- Checked: no part collides with the shells or with each other, the shells - Checked: no part collides with the shells or with each other, the shells
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
from 0 to -180 deg (CGAL intersections). from 0 to -180 deg (CGAL intersections).
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS - Open: component positions on the main board, Teensy cable plug size, LCD thickness, UPS
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` / hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board. `IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
+2 -2
View File
@@ -2,7 +2,7 @@
python export_3mf.py (from hardware/openscad, after the STL export) python export_3mf.py (from hardware/openscad, after the STL export)
Writes stl/remote_v2/remote_v2_top_multicolor.3mf: the top shell with its Writes stl/remote_v2/remote_v2_top_inlays.3mf: the top shell with its
two inlays as ONE object with three parts, in the same frame, each part on two inlays as ONE object with three parts, in the same frame, each part on
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
@@ -21,7 +21,7 @@ PARTS = [
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2), ("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
("remote_v2_text.stl", "ON-OFF inlay (white)", 3), ("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
] ]
OUT = "remote_v2_top_multicolor.3mf" OUT = "remote_v2_top_inlays.3mf" # remote_v2_top_multicolor.3mf is the owner's OrcaSlicer project
def read_stl(path): def read_stl(path):
@@ -94,14 +94,14 @@ UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */ /* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the // Cut perfboard, 56 x 80 mm (owner). Component positions are estimates from the
// owner's photos: measure before printing. Board frame: x across (0..52), y // owner's photos. Board frame: x across (0..56), y
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80. // along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
PERF = [52, 80, 1.6]; PERF = [56, 80, 1.6]; // measured by the owner: 56 x 80
// Held by 4 clamps on its long sides, no holes in the board (owner): a post // Held by 4 clamps on its long sides, no holes in the board (owner): a post
// beside the edge carries the board's edge on its inner half, and an M3 x 8 // beside the edge carries the board's edge on its inner half, and an M3 x 8
// button head with a washer (d7) in a heat-set insert in the post clamps it. // button head with a washer (d7) in a heat-set insert in the post clamps it.
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y PERF_CLAMPS = [[0, 4], [0, 68], [PERF[0], 4], [PERF[0], 68]]; // board frame: on the long edges x = 0 / PERF[0], at these y
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm) PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board) PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
@@ -493,8 +493,8 @@ module main_board_only() perf_place() {
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117 color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
// ribbon and display/IMU connectors at the edge, plugs on top (approx.) // ribbon and display/IMU connectors at the edge, plugs on top (approx.)
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]); color("#333") translate([PERF[0] - 8, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]); color("#333") translate([PERF[0] - 8, 44, PERF[2]]) cube([5, 11, 12]);
} }
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along) // GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)