2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF

- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by
  4 side clamps (M3 button head + washer into inserts), no holes in the board
- export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb +
  ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the
  owner's OrcaSlicer project
- STLs re-exported, README printing table and PLANNING notes updated

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-14 22:12:02 +01:00
1 parent 80270ba17e
commit 4aeb79dc89
6 files changed
+22 -16

No files matched your search

@@ -94,14 +94,14 @@ UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the
// owner's photos: measure before printing. Board frame: x across (0..52), y
// Cut perfboard, 56 x 80 mm (owner). Component positions are estimates from the
// owner's photos. Board frame: x across (0..56), y
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
PERF = [52, 80, 1.6];
PERF = [56, 80, 1.6]; // measured by the owner: 56 x 80
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
// beside the edge carries the board's edge on its inner half, and an M3 x 8
// button head with a washer (d7) in a heat-set insert in the post clamps it.
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y
PERF_CLAMPS = [[0, 4], [0, 68], [PERF[0], 4], [PERF[0], 68]]; // board frame: on the long edges x = 0 / PERF[0], at these y
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
@@ -493,8 +493,8 @@ module main_board_only() perf_place() {
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]);
color("#333") translate([PERF[0] - 8, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([PERF[0] - 8, 44, PERF[2]]) cube([5, 11, 12]);
}
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)