2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF
- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by 4 side clamps (M3 button head + washer into inserts), no holes in the board - export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb + ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the owner's OrcaSlicer project - STLs re-exported, README printing table and PLANNING notes updated Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
80270ba17e
commit
4aeb79dc89
6 files changed
+22
-16
No files matched your search
@@ -145,7 +145,7 @@ them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
|
||||
inlay (owner preferred a honeycomb).
|
||||
|
||||
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
|
||||
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01
|
||||
sits socketed on a cut perfboard (56 x 80, measured) with the nRF24L01
|
||||
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
|
||||
switch's plate sits on top of the case, body through the slot, and the old
|
||||
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
|
||||
@@ -197,7 +197,7 @@ charge/on LEDs show through two slots in the floor.
|
||||
- Checked: no part collides with the shells or with each other, the shells
|
||||
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
|
||||
from 0 to -180 deg (CGAL intersections).
|
||||
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS
|
||||
- Open: component positions on the main board, Teensy cable plug size, LCD thickness, UPS
|
||||
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
|
||||
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
|
||||
|
||||
|
||||
@@ -2,7 +2,7 @@
|
||||
|
||||
python export_3mf.py (from hardware/openscad, after the STL export)
|
||||
|
||||
Writes stl/remote_v2/remote_v2_top_multicolor.3mf: the top shell with its
|
||||
Writes stl/remote_v2/remote_v2_top_inlays.3mf: the top shell with its
|
||||
two inlays as ONE object with three parts, in the same frame, each part on
|
||||
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
|
||||
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
|
||||
@@ -21,7 +21,7 @@ PARTS = [
|
||||
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
|
||||
("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
|
||||
]
|
||||
OUT = "remote_v2_top_multicolor.3mf"
|
||||
OUT = "remote_v2_top_inlays.3mf" # remote_v2_top_multicolor.3mf is the owner's OrcaSlicer project
|
||||
|
||||
|
||||
def read_stl(path):
|
||||
|
||||
@@ -94,14 +94,14 @@ UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
|
||||
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
|
||||
|
||||
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
|
||||
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the
|
||||
// owner's photos: measure before printing. Board frame: x across (0..52), y
|
||||
// Cut perfboard, 56 x 80 mm (owner). Component positions are estimates from the
|
||||
// owner's photos. Board frame: x across (0..56), y
|
||||
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
|
||||
PERF = [52, 80, 1.6];
|
||||
PERF = [56, 80, 1.6]; // measured by the owner: 56 x 80
|
||||
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
|
||||
// beside the edge carries the board's edge on its inner half, and an M3 x 8
|
||||
// button head with a washer (d7) in a heat-set insert in the post clamps it.
|
||||
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y
|
||||
PERF_CLAMPS = [[0, 4], [0, 68], [PERF[0], 4], [PERF[0], 68]]; // board frame: on the long edges x = 0 / PERF[0], at these y
|
||||
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
|
||||
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
|
||||
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
|
||||
@@ -493,8 +493,8 @@ module main_board_only() perf_place() {
|
||||
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
|
||||
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
|
||||
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
|
||||
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]);
|
||||
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]);
|
||||
color("#333") translate([PERF[0] - 8, 8, PERF[2]]) cube([5, 21, 12]);
|
||||
color("#333") translate([PERF[0] - 8, 44, PERF[2]]) cube([5, 11, 12]);
|
||||
}
|
||||
|
||||
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)
|
||||
|
||||
Binary file not shown.
Binary file not shown.
Reference in new issue
Block a user