2026 remote v2: clamps for the 56x80 perfboard, generated inlay 3MF

- remote_v2.scad: main board is the measured 56 x 80 mm perfboard, held by
  4 side clamps (M3 button head + washer into inserts), no holes in the board
- export_3mf.py writes remote_v2_top_inlays.3mf (top shell + honeycomb +
  ON/OFF on filaments 1/2/3); remote_v2_top_multicolor.3mf stays the
  owner's OrcaSlicer project
- STLs re-exported, README printing table and PLANNING notes updated

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
mangavalkandClaude Opus 5.5 committed 2026-11-14 22:12:02 +01:00
1 parent 80270ba17e
commit 4aeb79dc89
6 files changed
+22 -16

No files matched your search

+2 -2
View File
@@ -145,7 +145,7 @@ them), strap tabs at the rear corners (it tipped forward), a hexapod emblem
inlay (owner preferred a honeycomb).
From the owner's photos and drawing: the sticks are JH-D300X-R1; the Teensy
sits socketed on a cut perfboard (~52 x 80, estimated) with the nRF24L01
sits socketed on a cut perfboard (56 x 80, measured) with the nRF24L01
(100 uF cap), an AMS1117, the ribbon connectors and now also the GY-521; the
switch's plate sits on top of the case, body through the slot, and the old
8 x 16 slot with d2 holes 19 mm apart fits it exactly; the UPS board's
@@ -197,7 +197,7 @@ charge/on LEDs show through two slots in the floor.
- Checked: no part collides with the shells or with each other, the shells
and the inlay don't overlap, kickstand clear at 0 and 70 deg, bail clear
from 0 to -180 deg (CGAL intersections).
- Open: perfboard size and holes, Teensy cable plug size, LCD thickness, UPS
- Open: component positions on the main board, Teensy cable plug size, LCD thickness, UPS
hole spacing; hand room untested; set `IMU_AXIS_FROM_CHIP` /
`IMU_AXIS_SIGN` in `remote/Config.h` for the IMU on the main board.
+2 -2
View File
@@ -2,7 +2,7 @@
python export_3mf.py (from hardware/openscad, after the STL export)
Writes stl/remote_v2/remote_v2_top_multicolor.3mf: the top shell with its
Writes stl/remote_v2/remote_v2_top_inlays.3mf: the top shell with its
two inlays as ONE object with three parts, in the same frame, each part on
its own extruder/filament (1 = case, 2 = honeycomb, 3 = ON/OFF text). The
part list is in PARTS below. Uses the PrusaSlicer 3MF layout (one mesh, the
@@ -21,7 +21,7 @@ PARTS = [
("remote_v2_inlay.stl", "honeycomb inlay (red)", 2),
("remote_v2_text.stl", "ON-OFF inlay (white)", 3),
]
OUT = "remote_v2_top_multicolor.3mf"
OUT = "remote_v2_top_inlays.3mf" # remote_v2_top_multicolor.3mf is the owner's OrcaSlicer project
def read_stl(path):
@@ -94,14 +94,14 @@ UPS_HOLES = 27.9; // +- u, not confirmed (same as the old remote)
UPS_Z = Z_BOT + T + 2; // board underside (2 mm standoffs); its top ends 2 mm under the plate
/* [Main board: perfboard with the Teensy 4.0 (socketed), nRF24L01, AMS1117] */
// Cut perfboard, 19 x 30 holes. Size and corner holes are estimates from the
// owner's photos: measure before printing. Board frame: x across (0..52), y
// Cut perfboard, 56 x 80 mm (owner). Component positions are estimates from the
// owner's photos. Board frame: x across (0..56), y
// along (0..80), Teensy micro-USB at y 0, nRF24 overhanging at y 80.
PERF = [52, 80, 1.6];
PERF = [56, 80, 1.6]; // measured by the owner: 56 x 80
// Held by 4 clamps on its long sides, no holes in the board (owner): a post
// beside the edge carries the board's edge on its inner half, and an M3 x 8
// button head with a washer (d7) in a heat-set insert in the post clamps it.
PERF_CLAMPS = [[0, 4], [0, 68], [52, 4], [52, 68]]; // board frame: on the edges x = 0 / 52, at these y
PERF_CLAMPS = [[0, 4], [0, 68], [PERF[0], 4], [PERF[0], 68]]; // board frame: on the long edges x = 0 / PERF[0], at these y
PERF_CLAMP_OUT = 1.5; // post centre outside the board edge (washer overlaps the board ~2 mm)
PERF_POS = [-36, 37]; // where the board's (0, 0) corner goes; x runs to -v, y to +u
PERF_Z = Z_BOT + 7.5; // board underside: 2 mm over the kickstand recess roof for wires (the Teensy USB plug then clears the display board)
@@ -493,8 +493,8 @@ module main_board_only() perf_place() {
color("#222") translate([2, 74, PERF[2]]) cube([11, 6.3, 6.3]); // 100 uF cap, lying
color("#222") translate([5, 58, PERF[2]]) cube([7, 6.5, 1.8]); // AMS1117
// ribbon and display/IMU connectors at the edge, plugs on top (approx.)
color("#333") translate([44, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([44, 44, PERF[2]]) cube([5, 11, 12]);
color("#333") translate([PERF[0] - 8, 8, PERF[2]]) cube([5, 21, 12]);
color("#333") translate([PERF[0] - 8, 44, PERF[2]]) cube([5, 11, 12]);
}
// GY-521 on the main board, on headers (board frame: 15.6 across, 21.2 along)