2026 docs: catch the READMEs up with today's state
- README: the HMI is generated turned round (nothing to set in the Editor); PC radio link: bridge mode done, no USB links any more, what's left (Unity driving the real robot, three nodes at once). - remote/README checklist: sticks and IMU checked, display uploaded, radio checked against the sim through the dongle; replace the IMU board. - CLAUDE.md: display runs the new HMI; next steps. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
This commit is contained in:
1 parent
1591105f26
commit
175a1a0da8
3 files changed
+41
-42
No files matched your search
+22
-25
@@ -72,36 +72,33 @@ Hardware (besides the electronics of the old remote):
|
||||
board clamps, no holes in the board), M3 x 40 + nut (kickstand pin)
|
||||
- M2.5 x 14 x 8 (joysticks, into their own boxes), M3 x 5 machine screws x 4
|
||||
(display, tap the posts M3), M3 self-tapping x 2 (UPS board), M2 self-tapping x 2 (switch)
|
||||
- Set the Nextion's display direction to 180 in the Nextion Editor: the
|
||||
display is mounted turned round so its connector clears the Teensy's USB plug.
|
||||
- The display is mounted turned round so its connector clears the Teensy's USB
|
||||
plug. `remote.HMI` is generated for that (display direction 270 in the
|
||||
Editor's terms, see [remote/NEXTION.md](remote/NEXTION.md)), nothing to set.
|
||||
|
||||
Design notes, checks and open points: [hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md).
|
||||
|
||||
## Planned
|
||||
|
||||
- **PC radio link (owner, later):** a USB nRF24L01 stick on the PC as the
|
||||
PC-side radio, on the same air settings as the robot and the remote, so Unity
|
||||
on the PC can both receive data from (telemetry) and send data to the robot
|
||||
and the remote. The stick is now reverse-engineered and reflashed with our own
|
||||
firmware (STM32F030 + Si24R1 + AT2401C); it shows up as a COM port and is
|
||||
updated wire-free over USB. See **[dongle/README.md](dongle/README.md)**. Still
|
||||
to do:
|
||||
- map the stick's LED and AT2401C power-amp control pins (app toggles them);
|
||||
- the radio protocol: today the remote only transmits a `CmdPacket` to the
|
||||
robot and nothing comes back. Three nodes need an address per node (or
|
||||
per pipe), a packet type byte, and telemetry back (e.g. as ack payloads
|
||||
or in time slots) so the nodes don't talk over each other; who has
|
||||
priority when the PC and the remote both send commands. Owner's
|
||||
decisions: the remote wins, with a toggle on the remote that hands the
|
||||
robot to Unity and lets the remote's sticks control Unity instead; the
|
||||
PC is the hub while it's online, the robot is the hub when it isn't;
|
||||
goals: mirror the real robot in Unity, drive it from Unity, remote data
|
||||
to the PC, and PC data to the remote;
|
||||
- Unity side: a serial-port reader/writer next to the simulation (the
|
||||
2019 generation already drove the robot from Unity, through the remote
|
||||
over USB: see `../2019-teensy-nrf24/`).
|
||||
- Remote battery level and the IMU on the normal pin headers: see
|
||||
[remote/README.md](remote/README.md), "Planned".
|
||||
- **PC radio link:** a USB nRF24L01 stick on the PC as the PC-side radio, on
|
||||
the same air settings as the robot and the remote. It's reverse-engineered
|
||||
and runs our own firmware (STM32F030 + Si24R1 + AT2401C, updated wire-free
|
||||
over USB), see **[dongle/README.md](dongle/README.md)**. Done (2026-11-17):
|
||||
its **bridge mode** lets the real remote drive the Unity simulation over the
|
||||
air, with the sim's telemetry going back to the remote's display as the ack
|
||||
payload ([sim/README.md](sim/README.md), "Using it in Unity"). There's no USB
|
||||
link to the remote or the robot any more; everything goes over the radio.
|
||||
Still to do:
|
||||
- Unity driving the **real** robot (the dongle transmitting instead of
|
||||
listening) and mirroring it;
|
||||
- three nodes at once: today the dongle answers the remote *instead of* the
|
||||
robot. Needs an address per node (or per pipe), a packet type byte, and a
|
||||
rule for who has priority. Owner's decisions: the remote wins, with a
|
||||
toggle on the remote that hands the robot to Unity and lets the remote's
|
||||
sticks control Unity instead; the PC is the hub while it's online, the
|
||||
robot is the hub when it isn't; goals: mirror the real robot in Unity,
|
||||
drive it from Unity, remote data to the PC, and PC data to the remote.
|
||||
- Remote battery level: see [remote/README.md](remote/README.md), "Planned".
|
||||
- Robot power: a stable 6 V supply for the 18 servos, see
|
||||
[hardware/openscad/PLANNING.md](hardware/openscad/PLANNING.md), "Notes for
|
||||
future designs".
|
||||
|
||||
Reference in new issue
Block a user